Replaced the PID board, no change in values on any test points. Submitted warranty claim for SWG, which is only 2 years old.

Question - if the SWG is bad, will the voltage at the cable feeding the unit be zero or near zero, which is what I am seeing? Assuming the resistance is zero or near zero, the Voltage in the circuit would be zero or near zero. Is this what occurs when an SWG is bad - resistance goes to zero?

shagymoe said:

Yes

Done

Click to expand...

Now the heater bypass actuator will automatically open and close when the heater turns on and off with no additional programming required.

Intake, Return, and Heater Bypass actuators will all automatically operate with changes in POOL, SPA, and HEAT mode.

I don't know what you want to do with your skimmer/MD actuator or why you need it.

dj,

Just to make sure...

The IntelliFlo3 does not have the same form factor as the standard WhisperFlo pumps.. This means that you will have to do a little plumbing work to connect the new pump.

If your old pump was not installed with pump unions, you will have to replumb anyway, but if you do have unions, the IntelliFlo3 is not a drop in replacement..

Thanks,

Jim R.

I understand. I have 220 at my pad so I will go with a 3hp. Will running extended hours at a lower speed cause more wear and tear on my salt cell?

djdonte said:

Why do you say I should spring for the 3hp?

Click to expand...

dj,

The bigger the pump the slower you can run it and still move a lot of water.

The slower you can run it the less it costs to run.

The slower you can run it the quieter it will be..

I have a older 3 HP IntelliFlo and run it 24/7, most of the time at 1200 rpm.. this costs me less than $20 bucks a month.. And.. the newer IntelliFlo3 pumps are much more energy efficient, then my old pump..

At that speed, you almost have to touch the pump to make sure it is actually running...

VS pump are really variable HP pumps... you just adjust the HP of the pump to match what you are wanting to do.

I am assuming that your current pump is being run from 240 VAC.. If you do not have 240 VAC at your equipment pad, then obviously, you should get the 1.5 HP pump.

Thanks,

Jim R.

Having only used hoses for 20 years on our last pool I can say hard plumb the filter! It seemed that I replaced hoses all the time. As Newdude said, they spring a leak or slit at the worst moment. I've come home from work with a hose deciding to become a fountain and once had the pool drain because it split.

I would prefer a drop in replacement as I was planning on a DIY install.. but if a convincing case is made for a new brand I'll work it out..

Jsf721 said:

Thanks for that user experience, How long have you had it?

My issue is this is a vacation home and I will be off site a few weeks. Guess I can have a friend baby sit it for me, I just don't want to return to a swamp - LOL

Click to expand...

We're just starting our 3rd season. I wouldn't go back to jugs of chlorine for any price.

I was away for 2 weeks last year, never had to touch the pool...FC was a little on the high side when we got back basically because no one had been using the pool and the cover was on all the time. Another trip for a week where the wife stayed at home using the pool, came back to FC being exactly where it was supposed to be - no interaction required.

Its not 100% hands-off, you still need to test and tweak if needed, but once you understand YOUR pool's demands, it's about as close to hands-off as you can get.

I also have some ad-hoc monitoring setup to ensure that power is getting to the pump/SWG etc, and some extra failsafe's beyond the flow-switch (if the pump stops, power is turned off to the SWG/Heater etc).

ajw22 said:

Did you create a feature circuit called “Heater Byass”?

Click to expand...

Yes

ajw22 said:

Valve B should be assigned to “Heater” circuit.

Click to expand...

Done

Buy a new filter.

You want to stay with DE or switch to cartridge? Many folks are switching.

Do you want a drop in replacement or some PVC work will be needed?

Waterway has good cartridge filters well priced.

Did you create a feature circuit called “Heater Byass”?

Valve B should be assigned to “Heater” circuit.

Be sure that the power is completely removed from the SWCG when the pump is not running.

PoolGate said:

Ah ok generally these are called "sun decks" but tanning deck is good too. So 1/2 the pool is a shallow tanning/sun deck and only a 16'x16' swimming area? How deep is the pool?

This is my 42'x22' with sundeck.

Click to expand...

Thank you for clearing that up for me

The sun deck size is 16 wide by 8ft, then a step down, then the pool slopes to a depth of 54 inches with no deep end (still discussing final depth.

Side note: Thanks for the discussion. It is helping me to think through everything. When I try to talk to my girlfriend about it all she can say is "Yes, do that!"

mtc89 said:

My sweep has been functioning very poorly for a few months, and finally not working at all. I took the wheels off to find the inner teeth nearly stripped smooth on the two-wheeled side, opposite side seemed fine. With my booster pump running and the wheels removed, I’m able to stop the drive axle with a light touch from my pinky. Is this normal? I think I’m not getting tons of water pressure from the booster, I’m wondering if there’s a leak underground.

There are rebuild kits on Amazon for like $100, but I want to be sure there isn’t something more profoundly wrong with the sweep itself.

Click to expand...

I have rebuilt mine at least twice. That turbine needs to replace every so often as that drives the wheels. Ensure that tube that leads to it is clean, not cracked or leaking.
Changing the gear wheels is important.

HermanTX said:

CircuPool is having an upgrade sale if price is playing a component in your decision.
Also, I read in another post that CircuPool was coming out with a model that had remote access to it. Suggest you call CircuPool and discussion your needs and see what they offer.

Click to expand...

Price is important for sure but want to get best most reliable system of one stands out. If equal I’ll go with price /warranty.

Dambra said:

Thanks! Any pics?

Also, is yours not the walk-on lid, as to why you ask the kids not to walk on it? I am being sold the walk-on flat aluminum lid by coverstar and told no problem for anyone walking on them at all.

Click to expand...

That's the one I have, I was told the same thing, but I choose the better safe than sorry method. Not the best of photos, but I attached a few and can get you some better ones.

+1. Mine had a shelf of old supply and a new batch around the corner.

Aeroknut said:

Agreed, and of course it’s the light furthest from the panel and we can no longer just change bulbs… is there any definitive way to tell between the globrite or microbrite while it’s installed? The bulb face is about 2” in diameter. When I zoom into pictures it ‘looks” like maybe only the microbrite has the protruding plastic tabs but dimension and description details seem to be lacking on the web.

Click to expand...

EXCELLENT SMITHERS! Thank u sir, that’s the info I needed. Bulb face definitely less than 2.25.

aldrichg9 said:

Nah his wording is just off
it's 16x32, with a 16ft wide 'tanning deck' is what he called it. If there is a better name, let me know.

No drawing yet - the builder and I walked it through onsite and I painted some lines on the ground where the pool would go.
Felt to me like he wanted to get an estimate in my hands so I could decide if I want to move forward from there.

Click to expand...

Ah ok generally these are called "sun decks" but tanning deck is good too. So 1/2 the pool is a shallow tanning/sun deck and only a 16'x16' swimming area? How deep is the pool?

This is my 42'x22' with sundeck.

HermanTX said:

CircuPool is having an upgrade sale if price is playing a component in your decision.
Also, I read in another post that CircuPool was coming out with a model that had remote access to it. Suggest you call CircuPool and discussion your needs and see what they offer.

Click to expand...

will call- thanks

Jsf721 said:

Same with suggesting vendors. Looking to purchase this week so I can have it installed ASAP.

Click to expand...

CircuPool is having an upgrade sale if price is playing a component in your decision.
Also, I read in another post that CircuPool was coming out with a model that had remote access to it. Suggest you call CircuPool and discussion your needs and see what they offer.

Jimrahbe said:

dj,

Well, it looks like you answered your own question...

I have only seen positive comments about the IntelliFlo3

Besides the optional relay card, you can also get an optional display..

You can get a 1.5 HP option or the 3.0 HP option.. I never, ever recommend the smaller 1.5 HP model.. I just beleive that bigger is better when talking about a VS pumps.

Here is a good link to the different options...

IntelliFlo3 VSF

Thanks,

Jim R.

Click to expand...

Thanks for the link. Those prices are good and the relay is already installed. Why do you say I should spring for the 3hp?