Latest activity
N
No Chlorine for Old Men replied to the thread The Chlorine Mystery - two brand new chlorinators, balanced water, no chlorine.
Good day Drew. Thank you for your prompt reply.
Wow... Okay I had a closer look at a far flat surface of the pool floor and I can see...
DrewLG replied to the thread The Chlorine Mystery - two brand new chlorinators, balanced water, no chlorine.
Welcome to TFP!
Your saltwater chlorine generator (SWG), running 8 hours per day, will add 5.7ppm free chlorine to your pool. With...
J
jfmorris replied to the thread Questions on mix of 2" and 1.5" PVC.
I’ve got a line level - that’s a good idea, that said, just eyeballing things today, with a tape measure at the skimmer and at the...
J
jfmorris replied to the thread Questions on mix of 2" and 1.5" PVC.
Oh certainly. I’ve replumbed the existing pad several times over the years, as I changed filters and pumps. I’ve always stuck with...
J
JamesW replied to the thread Tension break or freeze break?.
Can you pull the fittings apart?
N
NJ-Bob replied to the thread Considering Replacing Damaged Deck with Cantilever Deck.
Well, this took a hard left turn I wasn't expecting.
Allen, based on the red arrows (love those, by the way), I assume you are talking...
J
JamesW replied to the thread TA increased with ph minus.
Thanks for your support.
:goodjob:
MSchutzer replied to the thread Jandy Actuator & Spillover Feature.
It saves the setting by virtue of the toggle reversing switch being in the other position. It will stay reversed as it’s a mechanical...
N
No Chlorine for Old Men posted the thread The Chlorine Mystery - two brand new chlorinators, balanced water, no chlorine in Salt Water Chlorine Generators (SWG).
Long time lurker, first time poster, be gentle :)
The chlorine in my pool keeps dropping down to 0 after installing two different brand...
J
JamesW replied to the thread Leak from light conduit. (Junction box is 12” higher).
The installation manual says that the junction box needs to be at a specific level relative to the water.
So, you should probably just...
P
PGQ24 replied to the thread Maytronics Dolphin S400 Review.
I think the only difference is the price and the way they look. The important features are the same and limiting. 1 schedule task per...
T
TinFoilHat replied to the thread How high do you let CH go?.
I would want a similar pump to what HD has. I could buy a used one from them for about $225 but I could rent one four times before I...
wireform replied to the thread How high do you let CH go?.
Here's the 2" pump which I have in the 3" version which/and works flawless.
https://hftools.com/app63405
T
TinFoilHat replied to the thread AquaPlus "No Cell Power/No Cell Power 1" error.
Well, it is an aftermarket cell.... If you have one near you, Leslies can test your cells and maybe the PCB, but I can't remember.
A
AQUA~HOLICS replied to the thread Sun ledge/baja shelf build.
Build a rebar cage that is anchor epoxied (ASTM C881) per steel engineering plans into the existing shell and have that void filled with...
T
TinFoilHat replied to the thread How high do you let CH go?.
No danger of pop outs here. We have no water table above maybe 150' down or more.
O
ol_whistle_britches replied to the thread Just opened pool, Ph > 10 and CC = 5.5.
2 lbs of 53% Cal Hypo corresponds to 13 FC in a 10k pool, if I’m running pool math correctly.
After ~ 2 days.
@Newdude can you please...
HermanTX replied to the thread New guy here....
Welcome to TFP.
The pump suction should be connected to the upper port as that where skimmer should be located. The return to the pool...
proavia replied to the thread How high do you let CH go?.
Test your fill water and report baxk.
pH, TA, CH only
My bet is 7.7, 130, 225 🤑
HermanTX replied to the thread New Salt water pool.
Welcome to TFP.
Read
Start a thread under Construction and post info and photos. Get info on what to do before plaster is...
L
littlepool55 posted the thread Can an AGP return jet be too close to a ladder? in Above Ground Pools.
Drawing up deck / patio plans for my 18 ft AGP. We're replacing the a-frame ladder with a generic deck-mount resin one. Not big steps...
sirhicksalot replied to the thread Aiper Scuba S1 First Impressions.
I saw them at Walmart, but saw it was the N1 model. I didn’t know if that was different in any way, so I just got it directly from the...
U
Uhhello replied to the thread $30 Amazon Gift card for a legit Pool cleaning survey.
I completed a couple days ago. just got an email thanking and saying the gift card has been sent but never received it as of yet...
sirhicksalot replied to the thread Aiper Scuba S1 First Impressions.
I think it’s just a result of a lack of maintenance. The filter was disgusting when we moved in, and I’ve cleaned it twice since. Last...
O
ol_whistle_britches replied to the thread Upgrade Options?.
I just put in a 3hp calimar last week, based on the reviews here. It’s too cheap to pass up. If I understand correctly, your prologic...
HermanTX replied to the thread Should I install a valve before this pump (picture)?.
Some times is can be simplest of things - staring you right in the face. Glad it worked out and all is functioning as it should...