Latest activity
pjt replied to the thread K-2006 Taylor Test Results (50% Water Change).
That's the source of the high CYA.
Get pure LC, widely available at pool stores, Home Depot, Lowes, and Walmart (all sold in the pool...
PoolStored replied to the thread Intellichlor IC 40 Flow and Cell lights are off, Salt level lights flash red and green.
A blinking red "salt level" light on your Intellichlor IC40 indicates a low salt level.
How are you testing your water?
Do you have a...
1
1poolman1 replied to the thread Zodiac MX8 not working.
Most issues with a suction cleaner moving slowly are solved by cleaning the filter. It is usually a waterflow issue.
T
twe replied to the thread Intellichlor IC 40 Flow and Cell lights are off, Salt level lights flash red and green.
1
1poolman1 replied to the thread Zodiac sticks to walls.
Your footpad is worn out. Part W70327. This aftermarket one for about $9.00 works well...
J
JamesW replied to the thread Acid Wash vs Jack's Magic for copper staining (suspected high CYA levels, what to look for to assess risk to plaster)..
Not that much.
A better choice than replaster.
If you do a Jack's #2 first, that might do most of the work and the sanding can be very...
J
JamesW replied to the thread New install of jandy TCX won't turn on out the box.
Test the resistance with the board not connected.
Newdude replied to the thread Pressure gauge broken when I opened.
Looks like a GREAT excuse to purchase a 30 psi gauge that needs less squinting. It's a first world problem and i wouldn't have gone...
Q
QPSUtah replied to the thread Acid Wash vs Jack's Magic for copper staining (suspected high CYA levels, what to look for to assess risk to plaster)..
The sanding would still shorten the plaster life, but obviously would make it smoother to walk on, so still just a temporary solution.
ajw22 replied to the thread Help with Jandy Pump.
You need to get that working first.
What do the LEDs on the antenna show?
1
1poolman1 replied to the thread Pump/Motor starting to make some noise.
You will never see oil, there is none in a pool motor. Any lubrication is inside the sealed front and rear bearings and is a very small...
J
JamesW replied to the thread Intellichlor IC 40 Flow and Cell lights are off, Salt level lights flash red and green.
Post on youtube and link.
ShallowWater replied to the thread Drained Due to CH Pushing 1000ppm...
:D
1
1poolman1 replied to the thread Is this a superflo vs or whisperflo vs drive?.
Pump manufacturers don't make motors, they purchase them from contractors. Nidec is a large motor manufacturer.
Apparently Pentair had...
M
MelusineBeerCo replied to the thread K-2006 Taylor Test Results (50% Water Change).
I will get all the info from my equipment once it stops raining out. In the past, I used a shock/tablet combo from Leslies. Going...
J
JamesW replied to the thread Jandy pump failure.
Remove the capacitor and power wires and then test resistance from L1 to L2.
D
dldeuce replied to the thread Jandy pump failure.
Two black wires coming from the relay and the green ground wire. I cleaned up those connections a bit, but still nothing.
ajw22 replied to the thread Aqualink OneTouch Control panel with blank screen - pool is new to me.
Check the depth of the 1.5" pipe versus what the light needs.
S
SteveK52 replied to the thread Pump/Motor starting to make some noise.
Thank you for taking the time to respond. I have not noticed any water or oil but will take a closer look. We have had some rain this...
PoolStored replied to the thread Hi from Texas.
I think that is an OK move. Just know that it is an option...
Q
QPSUtah replied to the thread Acid Wash vs Jack's Magic for copper staining (suspected high CYA levels, what to look for to assess risk to plaster)..
Yes. And came back out today to look more closely. As expected the CYA is too high to test without dilution. One drop seems to obscure...
PoolStored replied to the thread Pressure gauge broken when I opened.
I remove mine, but they just go bad too.
https://tftestkits.net/Center-mounted-Pressure-Gauge-p78.html
1
1poolman1 replied to the thread Aqualink OneTouch Control panel with blank screen - pool is new to me.
Its been at least 20 years since I worked on the lenses of a fiber-optics light, but I believe that they are threaded into fittings with...
PoolStored replied to the thread Hi from Texas.
See Travertine and Limestone Corrosion section in the Wiki on Salt...
1
1poolman1 replied to the thread Pump/Motor starting to make some noise.
From that short video, it sounds like bearings. There also appears to be some white residue and a bit of rust at the very bottom of the...
PoolStored replied to the thread When Should I Add Salt.
You fusion specified 3000-3500 I'd aim for 3300.
Wait until temps rise a bit, will help the salt dissolve.
I'd recommend Diamond...
D
dldeuce replied to the thread Jandy pump failure.
