Latest activity
Bill1974 replied to the thread Hayward Tristar 2.70.
I assume you checked all the wire connections? power and RS485?
Can you connect the control/display panel on the pump to see if you...
J
Jenmachen replied to the thread ok, after much research, i still need help knowing which UV system to purchase/install.
ordered the paramount, looking forward to it!
T
TinFoilHat replied to the thread air leak repair.
The suction side has no pressure so any leak there will suck air in. Past the pump is the pressure side so any leak there will be a...
0
0xblurz replied to the thread Multi Port Valve Issue.
The problem was the skimmer issue you pointed out.
For the valve handle, ever since changing the gasket, it has now become loose. I...
Bill1974 replied to the thread Hayward variable speed pump question.
Get a meter out and check to see if the pump has power. As ajw22 stated the pumps display panel may be blank because it's disconnected...
proavia replied to the thread Did AA treatment, do I need to use Polyfill?.
Post a full set of current test results using your TF-Pro test kit.
FC
CC
pH
TA
CH
CYA
Salt
Water temperature
If you did an ascorbic...
Bill1974 replied to the thread Main filter pump breaker tripped.
Disconnect the pump or SWG and see if the breaker still trips when only one is connected. As state above also connecting the pump and...
Hi Everyone,
I have a 5 year old Omnilogic controller - which I normally love - which is now dead. Back in August we had what I can...
proavia replied to the thread Under Construction Pool - On Hold 5 Weeks.
Use to deteemine how much chlorine to add.
Is your test kit already on order?
Newdude replied to the thread Help with high CYA.
I wouldn't spend one penny or waste one ounce of effort with poor data. On any subject.
If doing an exchange then its fine because...
T
thiccflair21 replied to the thread Help with high CYA.
Ok read this and I hadn’t considered that I would need to buy another pump. I’m guessing it’s not safe to shut down the skimmer valve...
S
sdtfp replied to the thread air leak repair.
Yup, that's my answers.
I read the link you mentioned in your other post and wanted to make sure I understood. Air in the system is...
F
FrancisK7 replied to the thread Can you go TOO big with your filter?.
I received my filter today!
Can I buy any PVC bushing to go from 2" to 1.5" ? The Hayward manual says we have to use their kit.
It's...
C
courtHouston replied to the thread Attach pergola to patio -- worried about gas lines under patio.
The much-debated wooden 10x12 pergola in question. No, won't be cementing in the posts to an already-built concrete patio.
T
thiccflair21 replied to the thread Help with high CYA.
It’s my parents pool and they don’t want to spend $100 on a test kit.
J
JamesW replied to the thread Sta-rite Max E Therm 333HD.
Check the Fenwal for a Blinking LED.
Loss of Flame Rectification is common for a Service Heater with no associated Error LEDs on the...
K
Kaptain replied to the thread Pool Heater Suggestion in North Texas.
Not sure what your climate is, I live in the desert and we see lots of 100 degree days. Currently we are in the 70s to low 80s, with...
ajw22 replied to the thread Spa Return Not Working in Auto/Pool Mode.
Check the pump impeller for clogs.
Turn OFF the pump circuit breaker and reach into the back of the pump and see if you feel any clogs...
J
JamesW replied to the thread Gas vs normal exhaust smell on mastertemp 125 heater.
Check Stack Flue Temperature.
Check Flame Current.
Check Gas usage; it should be 125 cubic feet per hour.
Propane or Natural Gas?
Is the...
J
JamesW replied to the thread Sta-rite Max E Therm 333HD.
Service Heater or Service System?
Show a video.
The pressure should be a steady -0.2" w.c.
If it is erratic with steady inlet...