Latest activity
1
1poolman1 replied to the thread Replacing sand with glass media - What is the correct replacement ratio? How high do you fill with glass?.
+1, but it was already purchased.
1
1poolman1 replied to the thread can someone help me figure out how to get my cleaner to access the whole pool without getting stuck?.
Couldn't see it in the picture, but if the waterfall is actually the spa overflow, change the position of the valve so that not so much...
Katodude replied to the thread Help with Betta pool robot.
Both my Bettas are under warranty so I dont feel comfortable opening them up. Dont know if anyone else has done a battery replacement.
ajw22 replied to the thread Another Mastertemp 400 question .....
Considering your extensive list above I assumed you knew your way around the heater.
The "Fireman's Switch" is a poor name for the 2...
ajw22 replied to the thread Replacing sand with glass media - What is the correct replacement ratio? How high do you fill with glass?.
We do not recommend alternative medias for Sand Filters. There is no benefit to using it...
D
Dan-H replied to the thread need help with 2 inch pvc repair on rooftop solar.
here is one possible idea using an oversize Tee on the outside of the existing 2 inch tee.
Can someone tell me what size Tee has an...
T
TX-Pool replied to the thread Another Mastertemp 400 question .....
Thank you.
A silly question, when you say to restore the jumper are you meaning to remove the fuse that's in place?
I'll try to look up...
Lake Placid replied to the thread iCHLOR 30.
Please confirm you set production to 100% and the cell light stayed off……
W
Hi. Can anyone tell me if I have to dig my 2x12 supports down to grade height or can they sit off the ground. Is it dangerous for the...
J
JamesW replied to the thread Pool lights stopped working, PX300, iAqualink RS.
Newdude replied to the thread Reviewing AquaQuip/BioGuard directions from pool store (1st time opener).
Calcium is not needed in vinyl pools.
Lower the Ph 0.4 at a time with muriatic acid per poolmath. Mix for 30 mins, retest and...
ajw22 replied to the thread Pool lights stopped working, PX300, iAqualink RS.
I cannot see where the two probes are for each test.
For the 120V input test, you should test between the blue/grey/yellow wire and the...
1
1poolman1 replied to the thread Replacing sand with glass media - What is the correct replacement ratio? How high do you fill with glass?.
If you worry about this, it will make you crazy.
The recommended amount of sand that is initially placed in a sand filter is based on...
D
Dan-H posted the thread need help with 2 inch pvc repair on rooftop solar in Pumps, Filters, and Plumbing.
I have a small leak on my roof solar on one side of a 2 inch tee.
Open to suggestions on how to repair/replumb this.
ajw22 replied to the thread Draining Fiberglass Pool to Fix Main Drain Leak.
Your garbage can hack is novel and what I would try.
@Texas Splash may have ideas.
T
TinFoilHat replied to the thread Walmart 10% liquid chlorine more like 2% strength.
Probably old stock by date code. I've not had trouble with reasonable date codes from Walmart but this is Arizona and I do always look...
Y
yeamonn replied to the thread Reviewing AquaQuip/BioGuard directions from pool store (1st time opener).
I'm back! Some results were close others were way off. I'm now running the pump for 12 hrs a day and SWG for 3.
pH: 8.6
All: 100ppm...
Newdude replied to the thread Bring me up to speed on Vinyl Liner Pools.
A couple guys will hook the liner into the tracks and get it all centered
they cut in the drains (if applicable) and its filled to...
1
1poolman1 replied to the thread Please recommend a VS Pump best suited for my config.
To get the best performance for your pool, you need a big (2.7 or larger) high-head VSP. Your P4 will only "talk" to a Hayward VSP. The...