intellicenter

We recently built our pool and love all the equipment and IntelliCenter access on our phone. I have an iPad and want to make it a dedicated control device for the backyard that will connect with IntelliCenter, Sonos, Spotify, Smarthome, etc.. I would leave it inside or under a covered patio...

Hello I have an intellicenter controlling a dedicated intelliflo pump for my laminars and bubblers. I have Valve A turning on and off flow to bubblers and Valve B Tuning on and off flow to laminars. I have having trouble programming this is the intellicenter Circuit Groups. I tried creating...

Hello, I’ve connected the WiFi kit to my intellicenter control panel. I followed the directions (which are quite confusing) and I’m getting the following errors shown in the photos provided. It should be noted that I assume I did everything correctly because my panel says I am connected to the...

So, I have been lurking here for a while and just completed my DIY SWCG install last weekend, Just wanted you guys to check my work, inspired by threads from @MyAZPool. Pentair Intellicenter i5p installed with ic40 SWCG. I wired the SWCG on it's own relay but tied to the pump relay so it will...

I have a Aquacal heat pump model 166ARDSBNP (heater and chiller) that I would like to control via my recently installed Pentair IntelliCenter. With my previous Intellitouch, I had been told cooling was not supported in intellitouch. Pentair recently told me that both heating and cooling are...

Hello - I have a mystery. I have a intellicenter running two separate systems for pool and spa. When temp drops, both say that they are on freeze protection and the green light is on for both pumps on the app, but the spa pump flow is 0. I went and checked this morning, and the pump is not on...

Inspired by the post wiring Elfin-EW11 to Pentair Easytouch I'm documenting my installation of the Elfin-EE11 which is the ethernet version. I did this since the IntelliCenter came with an EnGenius ENS202EXT bridge to connect to the internet and came with a spare ethernet port. I opted to...

Hello all, I was hoping to see if anyone has seen this symptom on a new Intellicenter install. The intellicenter boots up and the License Agreement screen comes on. However, the touch screen is unresponsive and I am unable to click "I Accept". I tried resetting it, checked all wires and nothing...

Has anyone familiar with Pentair IntelliCenter know what this err message means? See photo It also shows if I do solar preferred. Does not appear if I select Mastertemp400 heater, only solar

Getting a high 4200ppm salt level reading from my newly installed Intellicenter connected to an older IntelliChlor IC20. I got a 3260ppm reading from a recently calibrated LaMotte Salt Tracer PockeTester. Are IntelliChlor salt detection not usually accurate, or is my Salt PockeTester in need of...

Hi everyone! I was wondering if anyone has any experience wiring equipment so that it will only turn on when the pump is running? I see there is the option to group "circuits", so my thought was maybe to group it into the "Pool" circuit... but I could use some specifics on if anyone has...

Hi All! I am in need of a Pentair 522035 Intellicenter Indoor Control Panel - does anyone know of a vendor with them in stock, or even better, does anyone have one they wish to sell? Used or new is fine! I have been searching for 2 weeks now with no luck Thank you..

Is anyone else having issues with accessing the Intellicenter UI via the App or the web? I've tried upgrading my panel to 1.064, which doesn't help. I'm inclined to think there is something wrong with the Intellicenter portal as prod.intellicenter.com and even intellicenter.com seem to be no...

I need to fix the board of my Intellitouch and as a result thinking of replacing my Intellitouch with the Intellicenter (using Pentair 522047 upgrade kit). I am quite handy and do most of these activities myself. I am planning to install the kit myself and have a couple of quick questions: -...

I just upgraded my IntelliCenter system with a Pentair 3hp variable speed pump from a single speed pump. I successfully connected the control wires to the panel. However the problem lies in a variable speed pump needs to have power all the time and right now when it calls to turn off it cuts the...

Hi all! This is my first post, and I'm a complete newbie on pools, but I am enjoying reading these posts, and look forward to learning and helping more in the future. Today my pool installer and I encountered an interesting issue on my new pool/spa. He'll call Pentair on Monday, but I thought...

i10ps Intellicenter control panel

My PB has installed an Easy Touch panel while I wait on a back ordered IntelliCenter. Is there an ‘Easy and Cost Effective” way to control this with my phone? Or a remote? Knowing I’ll be replacing within a few months… I have Pentair: 8 lights; VS Pump; Accessory pump; IC40 SWG Or do I wait...

Hi Folks. I've just completed my installation which includes an Intellichem governed Intellichlor all tied up to an Intellicenter. Despite all odds so far everything is going ok. I have a question though: is there any place I can see a log of each time the cell is activated and at what...

Hi All, A few weeks ago I discovered the Intellicenter does not like some features to be run GPM and others RPM for pump speed. I noticed this because when my schedule would get to that function it would stop and not continue running. Once I set everything as RPM it was okay. Then this morning I...

Hello. We installed a new Intellicenter late last year and have been having a lot of issues. First of all, it seems somehow my pump is no longer communicating with the automation, as the screen on the pump itself is active and the Intellicenter is reporting "communication lost". Additionally, I...

I’ll soon be installing a fiberglass pool with Pentair LED Lights, colorvision bubblers, and Magicstream laminars. Will I need a separate low voltage transformer to wire the LED lights or does the Intellicenter not need a separate transformer?

So I've been following the IntelliCenter upgrade and advanced automation threads started by @MyAZPool (Ron), and have been waiting for the right moment to upgrade my Pentair ET8 system that was installed during the original pool build in 2006. My goal is primarily to take advantage of some of...

Hey guys, just had new Pentair equipment with IntelliCenter installed a few weeks ago, all was fine until a few days ago when the whole system shut down. Coincidentally, this happened a day after we started heating the pool. My immediate thought was that the GFCI breaker tripped but it looked...

Is it just me or is IntelliCenter constantly down for periods of time? SSL error or json error. Seems like a pretty crappy platform.

I upgraded my pool automation from the Pentair Legacy Easytouch board to the Pentair Intellicenter board. I'm able to get my Pentair VSP pump partically working. I can't get it to bump up to a faster speed for when I set a schedule for the cleaner. It is my understanding that you can overlap...

Hey! I am interested in putting a valve actuator on the valve for my water fountain so I can remotely turn it on and off. I have the IntelliCenter and it is connected to 2 pumps (main/Polaris), the Heater (through the Gas heater control), and an Intellichlor60. 1) Will I be able to plug an...

When I got my intellicenter in February my solar line was already drained for the winter. Now that it is warming up in NorCal, I told my pool guy it’s time to use the solar. He just wants to fill the line and let it run with the filter all summer like it did with old Jandy controller. I...

I am looking at upgrading to an 8 from a 5 so I can separate out my bubblers and pool lights. Probably $750. Seems high to me any thoughts on this? Thanks

The fuse on my IntelliCenter has blown (and this needed replacing) twice in the last 2 years. My installer says that he has never seen this fuse go before. Does anyone have any suggestion for why this may be happening?