Latest activity
B
BilldaCat replied to the thread Nautilus Dolphin CC Plus stops moving after a couple minutes, bubbles.
FYI, the unit was bought in 2019, if it sheds any light onto potential wear/tear issues. I'm hoping the motor assembly isn't shot but...
H
haroldo posted the thread new pool build and owner - do cleaning robots really replace manual brush and vacuum? in Pool Cleaners.
I am planning on buying the best corded robot (which I think might be the Dolphin M600), and possibly the Skimmy companion. Before I...
W
Hi everyone. Hoping to get a little feedback here. I'm going to be getting a heat pump for my pool an automation controller, and...
PoolStored replied to the thread Pool Math APP - Free version.
Email [email protected]
PoolStored replied to the thread SWG Install and Opening Help.
No, likely you just killed everything.
Post a few pictures of the pool, include ladders and light in the pictures.
B
BilldaCat replied to the thread Nautilus Dolphin CC Plus stops moving after a couple minutes, bubbles.
Took it apart again, found one more leaf in the tracks, took that out, threw it back in the pool -- went for about a minute, down to the...
L
Luric9957 replied to the thread Pool Math APP - Free version.
In the overview it show No test logs for each of the measure item! There is no way to show anything except the addition in the...
reaton replied to the thread SWG Install and Opening Help.
Tested again 2.5 hours after my last LC dump and my FC is still at SLAM level. I went out and noticed the entire floor was murky so I...
PoolStored replied to the thread Results after testing while opening the pool.
When was the last time you cleaned your filter. It is small. You can get clearer.
Clean your filter, note pressure. When pressure...
ajw22 replied to the thread Connecting a Pentair Superflow VST pump to my Easytouch.
Time to show us the way the pump and SWG are wired in the load center and with the pump comm cable.
T
timjet replied to the thread Connecting a Pentair Superflow VST pump to my Easytouch.
Ok, this morning the pump came on as scheduled at 10 am on high speed which is 3000 rpm. But, the SWG was not on and the EasyTouch...
T
tenkas replied to the thread Results after testing while opening the pool.
Do you think this water is clear enough?
I've been holding chlorine at night for 3 days and cc is less than 0.5
I'm wondering if it...
ajw22 replied to the thread Liner floating up.
Welcome to TFP.
Pump the water out from behind the liner.
You will pump water out from inside the pool until the water level drops...
PoolStored replied to the thread New pool owner trying to understand test strip reading.
No. Post pictures of your equipment pad. Let's start there, then get you dialed in.
Post pictures of your equipment pad.
Thanks...
K
kbenedek replied to the thread Tension break or freeze break?.
P
phonedave replied to the thread Skimmer and Filter basket.
I clean my skimmer frequently. I don't bother to turn off my pump if it is running at the time.
Clearly you have to turn off the pump...
duraleigh replied to the thread White Cloudy Pool.
Good! Keep your chlorine SLAM values up. backwash if necessary although I don't think you'll need to.......you're in the home stretch
P
phonedave replied to the thread Can an AGP return jet be too close to a ladder?.
I used to have my return about 5 feet from my stairs. Now it is about 15. When it was closer my stairs required a lot less cleaning /...
P
Pas_pool replied to the thread New pool owner trying to understand test strip reading.
Thanks again. I plan to look through my pump manual this afternoon. So you would set it to run low for 24 hours. At 1400 rpm?
I don’t...
B
BilldaCat replied to the thread Nautilus Dolphin CC Plus stops moving after a couple minutes, bubbles.
Impeller looks clear to me .. any other ideas?
