Latest activity
this shows some leakage from pipes near the pool motor
Jimrahbe replied to the thread Easytouuch 8 Heater Overshoot.
WF,
In theory, when the EasyTouch is controlling the heater, the heater should be set to full hot (104). This is how it works..
The...
ajw22 replied to the thread Suggestion - search of log.
Development resources are limited for PoolMath.
My understanding is various charting techniques have been piloted and found to not be...
1
1poolman1 replied to the thread Where else to look for leak?.
If you can, start isolating the plumbing lines. Put plugs in the returns and leave the system off, obviously. No change, put a plug in...
R
ryuken83 replied to the thread Trying to SLAM a salt water pool.
FC-4
CC-1
TA-70
CYA-20
CH-375
J
JamesW replied to the thread Hayward GV-24 actuator on Dial-a-Flo?.
Can you remove the handle and show the valve without the handle?
You might be able to mount it on the Dial-A-Flo if the screws line up...
Mdragger88 replied to the thread Guidance needed, 3 years using TFP and I am at a loss (Solved).
In the pool
TopJimmy replied to the thread Threads on Atlas ORP Industrial sensor.
Here is my current dashpanel. Chemistry of pool and spa is largely the same:
250 CH, CYA <25, TA 80, FC 10
J
JamesW replied to the thread Bonding and grounding.
Typically, this means a "Listed" device that has been tested by a NRTL to conform to the standard for that device.
For example, a light...
1
1poolman1 replied to the thread The Ghost in the Machine is Back.......
Might try to disconnect any of the red RS-485 connectors on the left upper side of the board so that there are no inputs. If the problem...
N
nathandantzler posted the thread Mustard Algae keeps coming back - then Bromide mistake in Algae - Prevention and Treatment.
First off, I want to say this site has been a godsend. I've been using what I've learned here for the last 5 years, and my pool has been...
J
jendelta replied to the thread Sheer descents turning off.
Did both steps and still having the same problem
TopJimmy replied to the thread Threads on Atlas ORP Industrial sensor.
I used threaded tees (SxSxFPT) for pH and ORP. For the PRS & RTD I used a smooth tee with appropriately sized threaded bushing—couldn’t...
S
Hey there, I had my pool recently replastered. The deal was good considering the builder offered a new LED light. My old one was not...
H
hammer64 replied to the thread Pool plumbing question from New pool owner.
Tried the valves no luck. Are you referring to the line that goes to 1 1/2 inch pvc that goes into the ground and to the return jets?
J
jendelta replied to the thread Sheer descents turning off.
Yes, pump runs fine at 3450. Lowered RMP down to 2500 and still having the same issue
J
JamesW replied to the thread Hayward GV-24 actuator on Dial-a-Flo?.
1
1poolman1 replied to the thread Filter pressure after transition to cellulose fiber.
Its not unusual at all for the pressure to be much less with cellulose fiber, as long as the correct amount was added. First started...
H
hammer64 replied to the thread Pool plumbing question from New pool owner.
Ok. I’m going to get to the store for the proper lube
H
hammer64 replied to the thread Pool plumbing question from New pool owner.
Water level and doors are good, tried each individual line into the pump by itself, so other two turned off. Tried them all for 30...
C
My solar touch ET has lost com w/ pump. I tried all the normal fixes (power off/on; cable is secure; reseet, etc. Any clues as to why...
J
JamesW replied to the thread Hayward GV-24 actuator on Dial-a-Flo?.
It cannot be mounted on a Dial-a-Flo, but you might be able to pull out the insides and replace them with the insides from a Jandy style...
PoolGate replied to the thread The Ghost in the Machine is Back.......
Yes and this is what I did. I open when it gets to around 60. I opened to the above mess and it was below 60. Right now sitting at 58...
W
wireform replied to the thread The Ghost in the Machine is Back.......
Here on TFP the calendar date for pool opening is not a date you pick in your mind but rather the water temperature getting close to the...
kevinanton7 replied to the thread First Time Pool Opening - CT.
So the CYA dissolved yesterday. We didn't have enough to get up to 'normal'. This morning we had the following:
FC - 8
CC - 0
pH -...
P
phonedave replied to the thread Screw in bead liner receivers?.
I see no benefits to using an in ground bead receiver in an above ground pool, and I see LOTS of downside.
Donldson replied to the thread Solar cover only (no heater)?.
Of course it makes a difference, but it's not going to let a pool stay at 80 degrees when the air temperature is consistently below...
Sabot replied to the thread Threads on Atlas ORP Industrial sensor.
How did you tap into the PVC? Did you use something similar to the drawing that I attached? If yes, where did you purchase them?
