hayward

Hello. I have Hayward Omnilogic with two VSP motors, a chiller, a heater, lights and a water feature. On Sunday morning the system had turned itself on running the filter at 76% and two of the regular schedules turned off. Every time I turned it off and the schedule back on within seconds it...

Having discovered that Paxcess has some shady practices, I'm now looking at the Hayward 250li. I want cordless. Anyone here have one? Pros? Cons?

I connected my Aquarite to my OmniHub the other day via the daughter board just like in this thread. The OmniHub is communicating with the AquaRite to produce chlorine. I tested it over night and the chlorine level increased as expected per a FAS/DPD test. Also, the scheduling seems to work...

I just got everything finished on my new inground pool and need some guidance. Do I need to put shock since it has a salt cell? How much muriatic acid to bring my PH and Alkalinity down? It is currently at 8 and 123, respectively. Leslies said their system will not give a dosage for the...

Hi I have a Hayward RS1500 pump and was redoing some piping. The outlet at top has inside and outside threads, does anyone know what size fittings those are? The previous setup looks likes a 2 inch internal coupling, but taking it down to the big box store the male part seemed a little loose, so...

Hello. Dig day! What do you all think of adding an additional light to the deep end? Builder wants another $1600. Will add details on the build when I get more time.

Hi All, Just posting this for anyone else who may run into it. I have a Hayward Omnilogic system with UCL lights. After updating my firmware to 4.x my lights started behaving very strangely. They would flicker off and on sometimes, or would transition colors suddenly instead of gradually...

Hi all, Novice repair person here. My Hayward spa heater (installed 2018) is not heating the water and is displaying this LO code. I have read every troubleshooting guide and watched every video I could find. My diagnostics included: 1. Cleaned the filters, even ran the pump without the...

We have noticed that our Hayward heater in Spa mode with Set point to 98 degrees will drop down to 95-94 degrees (as reported by Omni logic) before kicking back on. Is there a way to adjust the sensitivity so that it will turn back on? In some instances we find ourselves manually toggling the...

Hello, I have a Hayward PowerFlo Matrix Pump (1.5HP, 115V) that is only a few months old. The other day when I went to turn it on, it only made a humming sound and was not working (it was only off for about two days. I usually run it for 8 hours a day). After a few seconds, it shut off. I...

I have a 4 wheel Hayward and it gets stuck on my Paramount SDX drain cover. I can’t find any bumpers or clips made specifically for this cover. Other than switching out the cover does anybody have any other ideas?

I just got the hayward sand filter leaking from the clamp. It started recently. I also find the lever of the control valve hard to move around. Do I replace the control valve, O ring and the clamp? Or is there anything else that I am missing. I have added a video below for understanding the...

I have a Hayward SP0410X502S Micro-Clear Slide Valve Assembly. I got this to replace a worn out one when I installed a Solar pool pump system about a few months ago. Now when I try to backwash the DE filter it sucks the valve back down into the normal opperation position. Heres a link of my...

Hello Folks, my pool pump has been loud for about 2 months, not knowing much I figured it had to be replaced soon so I was trying to get through the summer. We just moved in to a house last year and I know everything in the pool is original from 2014. It's a salt water system. Last night the...

I have a Hayward 350FDN, it was working earlier this year and now gives the IF error. I had our gas company come out and bump up our supply from the meter and replaced the flame sensor. Still get the error. I can see through the sight glass the igniter turn red and flame for a short time (3-5...

I have an Aquarite chlorine generator that's probably around 20 years old but had its board replaced within the last 5 years. My Hayward T-CELL-15 started failing after only 2.5 years. Due to the significant increase in prices and low availability on Hayward's salt cells, I decided to give the...

I am replacing A 1.5hp 220 pump. Hayward control box(timer and pump speeds). I am installing a powerextremeusa pump. It has a low, common and high connection. The controller box has 4 wires. Green ground, black and red loads and orange. My question is what goes where ? I want to control ether...

Equipment-Hayward 1.85 THP Variable Speed Pump OmniLogic automation All installed spring 2020 by previous owner/ builder. Under “Select device” I see: MSP. HUA 00-4c-07-f4-a6 version R3.2.0 MP 01-47-07-f3-f8 version R 3.0.0 MSP id 85587 (not sure what this means) Problem: CommLoss...

Our pool was installed around 2007 and still has the original Hayward H400 heater. We had the original Jandy board recently replaced with the Zodiac iAqualink. The iAqualink system is great, and the heater does a good job at heating water, but the issue is the communication and/or relay between...

We have 19" sand filter from XtremePowerUS at Amazon with 1.5 HP pump. We add more sand and somehow the center-core diffuser assembly was moved. The more we move this center core, the more it floats up. How can we bury this filter diffuser core assembly back into the bottom of the sand inside...

Does anyone know if Hayward honors a warranty for a new SWG (entire system) when purchased on Amazon? Their warranty page specifies "Hayward authorized seller" but didn't know if that included Amazon. I emailed them but haven't received a response. Background: I am replacing a T-9 cell, but...

I picked up a Hayward H100ID Natural Gas heater and finally got around to hooking it up. It turns on and the exhaust fan spins, but no clicking from the ignitor or firing going on... slowly troubleshooting the connections, any recommendations on what to look at first? I've gone as far as...

The issue started this season. My Hayward hp21104t would flip the circuit breaker after running for a few hours. Now it's throwing a LP (Low Pressure) error and won't start at all. Based on my limited knowledge and research, this error is related to refrigerant but can really be thrown because...

I have an issue that I can't find any other posts on, and I hope someone can shed some light on the fix for it. My Aqua Logic PS-8 / Hayward GLX-PCB-MAIN system is putting itself into Service Mode every 1 to 2 days. It started happening after I turned the system off and replaced the electric...

Hey guys, opened the pool, hooked up the pump as usual. The displays turns on and shows the pump running, can stop it, pause it, change speeds...BUT nothing happens with the motor, it just doesn't run at all. I have seen that a lot of people have "humming but won't start" issue, but here its...

My husband and I bought a house that came with our pool and equipment. We have been struggling for over a month now to clear up the cloudiness with the SLAM process and Taylor k-2006 kit. We bought a new hayward cartridge but it didn't improve anything. The pump will randomly shut off at times...

Just fired up the heater [Hayward H400ED2] for the first time this season and boy did it make a racket! Pipes were bouncing around and it sounded like an animal was stuck inside trying to get out. Poking around on the internet, it seems like it's likely the thermocouple valve. The heater is...

Hello, I have a customer with a hayward pro logic system with a T cell 3 on it. 2 days ago i got the notification that the salt level was very low and when i checked the system it read 600 ppm which is weird because we had no rain , fresh water wasn't added to the pool and the level last week...

Former owner seemed to rig this to work and it got hit by a excavator which cut a cord, the other actuator then shorted and almost melted the connectors together before blowing the fuse. Managed to get that out and replaced both actuators and the fuse. I can get them to spin working the switch...

My heater will not fire on its own. I can jumper across the remote terminal block to get it to fire. I am wondering, since I don’t have a remote, is it a corrosion issue as it appears the terminals (2) are just looped back to each other? If I clean them up and it still doesn’t fire, can I...