Latest activity

Posts Threads Hot

Latest activity

 Media Forum list

How to use Pool High manually from EasyTouch 4

D
Jimrahbe said:
Dave,

"Pool High" is just a Circuit Name.. It could be "Jim"... It is just a name, that by itself, does nothing..

What does it do on a schedule?? I suspect it just changes the pump speed.

I don't see how you could assign it to the heater button... :scratch:

If it just changes the pump speed, then most likely it is a Feature Circuit.. If that is the case, it can be turned on or off by using the little 3" LCD

Menu, scroll to find Feature Circuit with a name of "Pool High" and turn it on or off..

Edit... What is it you are actually trying to do??

Thanks,

Jim R.
Click to expand...

Edit: Well, nevermind. I just read through the manual and it says that the Solar button can only be used in Service mode. But it also says the same thing about the Heater button, and also that it does not activate the pump(!), so now I'm curious about what I thought was going on with Customer B's panel. We shall see....

Edit 2: The plot thickens! The manual says the Solar button can be used outside of Service Mode to control the AUX EXTRA circuit. It looks like I can assign Pool High to AUX EXTRA, set it as an egg timer schedule and activate it with the Solar button. I will post back my results.

Thanks, Jim. I knew that about the circuit name, and Pool High does in fact just kick the pump speed up for the cleaning cycle.

Scrolling through the menus to toggle a circuit is more complicated than I'm interested in, and I'd just as soon put the panel into timeout and hit Quick Clean on the pump.

I have another customer that I'm certain has the heater button programmed to run a higher pump speed and nothing else (he has no heater), but I'll have to check this when I'm at his pool this coming week. I don't know if Heater and Solar operate differently, but I'll confirm and, if I'm right about Heater, I'll poke around in the settings to see how it was configured.

Customer A has his panel connected to a Screenlogic interface which would be just fine, but something happened with his home internet and now neither of us can connect to Screenlogic from the app.
Click to expand...

Pentair IC60 creates chlorine when first turned on and then flashes "inspect cell"

ajw22
fabsroman said:
An analogy that I can use is a vehicle starting up, you driving a mile down the road, the vehicle deciding that the mpg/efficiency of the engine is not optimal, and then shutting down. I guess another vehicle analogy is that an emission sensor returns a code and the vehicle's computer just decides to shut down.
Click to expand...
I have owned cars like that. :D
Click to expand...

Pentair IC60 creates chlorine when first turned on and then flashes "inspect cell"

F
ajw22 said:
Seems the cell was not insane all along.
Click to expand...
Yeah, you continue to harp on that.

I still think it is insane that it WILL produce chlorine upon startup, but it then determines that the parameters are not good enough to create chlorine anymore.

An analogy that I can use is a vehicle starting up, you driving a mile down the road, the vehicle deciding that the mpg/efficiency of the engine is not optimal, and then shutting down. I guess another vehicle analogy is that an emission sensor returns a code and the vehicle's computer just decides to shut down.

Sort of like somebody saying, "Sure I can do it, but I just don't feel like doing it because it is too much work."

Sounds like insanity to me, but we can agree to disagree on this one.
Click to expand...

Old Chlorine - Check Mfg Date if you can

ajw22
I wrote about that recently...

Educating the Pool Store

I like supporting local family run business and I think we need more of them in our towns. There is a local pool store , family run by the 2nd generation brother and sister, where I buy liquid chlorine, muriatic acid, salt, and small stuff I need like the tail scrubber for my Polaris cleaner. I...
www.troublefreepool.com www.troublefreepool.com
Click to expand...

Test after opening salt pool

P
PoolStored said:
Yeah, turn it off, and let FC come back down into range for your CYA. Link-->FC/CYA Levels
Then turn it back on.
In the future, tell them you want a "no chemical" opening at a reduced cost.
You can handle startup.
Click to expand...
Totally also because the only thing they put is LC…..
Just surprised about their salt reading at 1000. They were ready to add 200 LBS of salt…..crazy
Click to expand...
  • Wow
Reactions: PoolStored

New EVO 614i Robot Pool Cleaner Review

T
Jim,

This morning both buttons worked just fine. It seems there was some sort of electrical connection issue in the switches that wore off after many presses. I saw the blinking (once or twice) of the power light today that let's me know the robot is ON. However, this afternoon the Start/Stop button had problems again. Rapid pressing again did get it to turn ON, so I'm thinking it will just improve over time.

If others have problems initially with the buttons on the control box, just press them firmly many times in rapid succession. That should get you going.

For the dust, I don't really mind that it takes a few runs to get it up. It is such great help to me versus manual vacuuming that I don't mind it at all. I do need to help it out a little in areas like corner platforms, steps and sharpish pool corners, but I just brush those to the bottom and the bot gets them there. Yes, I use the optional Fine Filter Canister (it is truly EXTRA fine!) and recommend that to others if you have fine stuff to vacuum up.

And the filter is so fast & easy to clean! Just spray it briefly with water and everything just slides right out.

Until I make or buy a caddy, just a couple of 7-inch scrap 2x4 pieces side-by-side works well to elevate the treads and brushes off the floor for storing out of the pool (and in the shade).
2x4 robot platform.jpg

Thanks Jim, for your robot (and other) expertise helping everyone here.
Click to expand...
  • Like
Reactions: Jimrahbe

2x4 robot platform.jpg

T
2x4 robot platform.jpg

Damaged Waterfall Weir

M
1poolman1 said:
Spoke with a friend who is a builder. While the diagrams usually show the installation in a horizontal orientation, the fixture can be installed in any way that will provide the desired effect. That may be what the builder of your pool did.
Its not pressure, but flow, that determines the way those falls look, usually requiring 20 - 30 GPM/foot of length.
Click to expand...
Thanks for the additional information. If this waterfall fixture is designed to be installed upside down, as it was in this case, then the design would have considered water that is retained after winterization, and that shouldn't have been the cause of the damage. So still curious about that.
Click to expand...

1746221997258.png

ajw22
1746221997258.png

RPM changes for Intellitouch Not Holding when using phone or computer

P
I am in the screen logic app on my phone. This is within the speed control portion of the app, not pool or cleaner although they are indirectly affected because the speed set in Pump section tells the pump what speed to run for each of those settings. Here is a screen recording. You can see when I change the speed of the last two, they just revert back and actually change the speed above them. When I change the speed on the Pool setting at the top, it holds, maybe because it doesn't have a setting above it, IDK. Turns out I can't attach a screen recording. but here is a screenshot I have used for many years to change speeds.

Oh, and you can change the speeds with the remote. I believe it is/was called the Mobiletouch. I still have it laying around so I tried that too to no avail.
Click to expand...

Attachments

  • Screenlogic Pump Speed.jpeg
    Screenlogic Pump Speed.jpeg
    104.1 KB · Views: 6

Compatibility with Blue Torrent variable speed pump/filter

PoolStored
1poolman1 said:
Click to expand...
Dead link for me...

poolpartstogo.com

Automation-Capable Variable Speed Pump Adapter

This keypad replaces the original keypad for a Blue Torrent Cyclone, Sunnora, or BLACK+DECKER Inground Variable Speed pool pumps. It provides all the same functionality as the original keypad, but also includes the capability for relay-triggered control to allow virtually any automation system...
poolpartstogo.com poolpartstogo.com
Click to expand...

Old Chlorine - Check Mfg Date if you can

D
Bought 3 pack of HDX 10% Chlorine at Home Depot. Put it in pool and tested to .5 PPM. Looked up code on the box and it was made on July 25, 2024, Liquid Chlorine loses 50% of its potency in 6 months and 90% in a year.
I only knew because the 3 pack box had a date code on it and TFP has a code conversion in the forum. Going back for a refund. They should be ashamed.
Click to expand...

Compatibility with Blue Torrent variable speed pump/filter

1
justjenn33 said:
How do I check the if the connection is RS485? The model is BT-IGV150.
Click to expand...
That pump is the same as the Calimar/Circupool/Black&Decker. It will require the automation adapter to be controlled somewhat automation. It allows relay inputs to change the speeds that are set in the motor itself. That makes any brand automation able to have some control.
Click to expand...

Hayward DE Filter - reassembly question

1
pgershon said:
I went to put it back on and it looks to me like it was broken off. I reattached the filter with the rod hanging down, which is how it was. But I suspect it is all supposed to be one piece. Hopefully this will at least be an improvement as the filter is clamped on. I ordered a replacement as well. Photo shows the two pieces.
Click to expand...
What "rod hanging down" are you taking about? If the stainless through rod that holds the whole grid assembly together, it is supposed to have a nut and washer at the bottom spreader and wing nut and washer at the top so the whole assembly can be taken apart and then held together by that long rod that is threaded at each end. it doesn't just hang down.
For now, you can take that broken part out of the manifold and install the part with the sock into the manifold. The sock should be held on with a clamp.
Click to expand...
Load more

Filter

Top Bottom
Back