screenlogic

I came back from a month long trip and my screenlogic app is no longer working. I’m in FL so we often have storms and prolonged power outages. I can connect to the app but it doesn’t show temperatures and the controls can be used/turned on in the app but they aren’t turning anything on in my...

Hi everyone, Need assistance in setting up a schedule for our "inground Cleaner" & "VSP Pool Pump". Question: If i setup pool pump to run 12 hours, say 8am to 8pm daily...and I have a schedule for CLEANER to run 1pm to 5pm daily, is this system smart enough to know when to run the Cleaner...

Hi everyone, I am pool newbie. Pool was installed late last year. Toward the end of the season, we had a power surge that fried our salt cell. It was replaced for free but after they replaced the equipment I lost control of my pump speed through the screen logic app. The pump now only runs at...

Hello, Brand new to pool ownership and we finally finished our pool construction project. I'm having some issues with ScreenLogic though. I have ATT Fiber for internet. My ATT modem is capable of routing but I have an Orbi mesh, so I configured the ATT modem to be in bridge modem and...

This is the opposite of what everyone else normally asks about how to turn off the delay. I want to create a delay (the same as the pool cleaner delay) before the heater turns on in the intellitouch/screenlogic software. After 2 years of monitoring the heater behavior (Mastertemp 400) as we...

I had a working schedule with 2 overlapping routines until a few days ago when I mucked with the circuits and the Intelliflo setup in an attempt to change (make slower) one of the 2 active pump speeds scheduled. Now only one of them is working as scheduled...the one I did not touch. What is the...

Greetings all. We have a new build and Pentair came out yesterday to do the basic programming which was pretty much the last step in the installation. Surprise surprise, we can no longer control the pump at its controls (learned this is normal) and double surprise we learned that The Android...

New pool, first time post, thanks in advance. I just had pool/spa redesigned with all new Pentair equipment; EasyTouch4, Intelliflo VSF, Mastertemp 400, Intellichlor IC40, two Hayward PSVs. I wanted my pool contractor to add a Spa Low feature circuit but nothing he has tried works; the valves...

I have just upgraded from Compool to a Easytouch Upgrade Board ( Kit (P/N 521107) - For upgrading CP3xxx systems) I also have the wifi-kit (screenlogic 2) all setup and working great. can controll all with my phone now. I have an existing salt system that is woking perfectly : Question is : how...

I’m struggling with our ScreenLogic app. Our Pentair system displays the correct date and time (say Thursday, April 28 6:08p). However, if I set a cleaning cycle for Thursday from 5p to 10p, nothing happens. However, if I set it for Tuesday from 5p to 10p, the cleaner turns on. Why would there...

Hello! New pool owner and have a question. My pool has 2 Pentair VSF motors. I do see a section in the app (under pumps) to control the speed but that speed is not tied to a schedule... hence I can't configure it to run at a lower speed and speed up later during peak hours. Am I missing...

I'm having a lot of trouble installing a ScreenLogic protocol adaptor to my system. I have Gigabit internet and Linksys MX4200 routers. I've spent countless hours on the phone with Pentair and they can't seem to resolve the issue. It seems that the screenlogic is not communicating with the...

Hi all, new to the forum, thanks in advance for any help you can offer. I have an EasyTouch4, Intelliflo VSF, iChlor, and Screenlogic2 connected to J20. It was all working fine until a bad storm rolled though. Because so many things were not working, I replaced the main board. Currently, I...

I got a new router and it is distributing the same IP addresses I believe. 192.168.1.0/24 however I cannot seem to get it to connect to the outside unit. The screenlogic connect software can see the adapter however when i try to start the software it shows no signs of actually being connected...

This is probably a simple fix, but I haven't figured it out yet. I upgraded my computer system to Windows 10 and now I can't seem to get the Screenlogic Connect to recognize my system. My router works fine, I reset the protocol adapter, re-booted everything. The wireless link interface has a...

I received a message from a client mentioning a lack of remote access to their automation. So far I have made an attempt to login (via Android Screenlogic Connect) and received a result of a spinning wheel and window with the text of "Login failed. Please check: Password Wifi or cellular data is...

Decision: Buy a new Pentair protocol adapter which hopefully fixes my communication issue with ScreenLogic or buy upgrade kit to convert Pentair Easytouch 8 to Pentair IntelliCenter (522047) Background: My Easytouch 8 is about 4 years old. Protocol adapter is bad. Diagnosed with some helpful...

Hi, A couple of weeks ago I set up the Pentair Easytouch controller. I wired up the Wireless Transceiver and connected it to my iPhone. I then set up ScreenLogic on my pc and started to set up a schedule. I could read the pool and air temperatures, work on schedules, and other things on both my...

Issue: If my pumps are running and I open Screenlogic on my Android, my pump shuts off for about 10 seconds, then resumes normal operation. When I do the same thing with ScreenLogic on my Apple device or computer I have no such problem. I spoke with Pentiar tech support and they said my configs...

Im not sure if Im doing something wrong or if my equipment is not compatible. I ordered the Pentair ScreenLogic Wireless Connection Kit 522620 and pentair screenlogic2 protocol adapter separate. Every thing is connected correctly so I think, when I try to connect locally via the pentair app it...