easytouch

Been reading a lot of postings and very appreciative of all the great info and contributors. Finally ready to pull the trigger on pool automation but have a few questions hopefully you can help me with. I have the Compool LX3800…..which I assume means I’m a candidate to upgrade to easytouch...

Hi all, new to the forum, thanks in advance for any help you can offer. I have an EasyTouch4, Intelliflo VSF, iChlor, and Screenlogic2 connected to J20. It was all working fine until a bad storm rolled though. Because so many things were not working, I replaced the main board. Currently, I...

I was hoping to get some clarity around smart/app based system. My PB is using Pentair products and is offering EasyTouch for upgraded Smart functionality. I have been reading online and most of the information I find is Intellitouch from Pentair. Is there a difference between EasyTouch and...

Hi all, first time poster. I've spend a few hours reading through the various threads trying to make sense of everything and I think I know enough to be dangerous but could sue some help. I'm currently building a 15' x 25', 13,000 gal, outdoor, in-ground concrete pool and I'm trying to decide...

I have an Easytouch 8 setup with a wireless controller(UWC) and one wired controller (UIC). All were setup/installed in 2016. The controlled did have a spill into the spa and it was replaced under warranty (only the handheld remote portion, not the wired antenna). I don't know if that matters...

Hi all - i am looking for some pre-work help to ensure I don't screw up when replacing my Pentair motherboard. I have read and seen the following tips and wonder if you have others to share than the below... 1) be careful not to touch the board too much and only touch the edges if you can 2)...

Hey all, My easy touch 8 controller seemingly randomly opens the solar valve actuator during the night. The control panel doesn't say that solar is activated, and the solar sensor is well below what it would be during the day. It sometimes happens when I have my cleaner program running, or when...

Hello, Long story short, I am having an issue reconnecting my Easytouch Wireless Remote back to the Easytouch 8 panel. Looking for some help or guidance. I have tried the menu -> settings -> "Wireless Address" routine with no luck. My main control panel came as Easytouch 8 chassis, but it...

Hi, A couple of weeks ago I set up the Pentair Easytouch controller. I wired up the Wireless Transceiver and connected it to my iPhone. I then set up ScreenLogic on my pc and started to set up a schedule. I could read the pool and air temperatures, work on schedules, and other things on both my...

Hello, This is my first post, I would like to start by thanking the community for all of the valuable information on these forums! I am reaching the ending stages of a new pool build and have decided to incorporate a pentair easy touch 4 control system (p/n 520914). In addition to controlling...

I just replaced a circuit breaker and then powered-up my 9-year-old AquaCal SuperQuiet pool heater, and now the heater will not start-up. The heater display board gives a CEr indicator (communication problem). Likewise, my 9-year-old Pentair EasyTouch remote control system in the house now...

I am planning to add some basic automation to my pool. I just recently upgraded all my equipment and redid the pad. What I’m looking to do is be able to turn the heater on and off when away from the house and use Alexa to turn the slide on and off. I will be doing the installation myself. I was...

Good day everyone. What a great resource this forum and site has been overall. Thank you. I mounted up and wired the Pentair EasyTouch 8p, one body of water, no spa. I have 3 12V pentair lights, a Pentair 011018 IntelliFlo Variable Speed filter pump, a Pentair 011519 WhisperFlo water...

We have a new Pentair EasyTouch controller with a Leisure Pools Pool/Spa combo. It's plumbed so it can either be in Pool mode or Spa mode. I've noticed the control unit keeps switching the valves back and forth from Pool to Spa about every 20 minutes. There are no schedules set and no egg...