Well let it get 2-3 degrees warmer and climb in!! I'm heading out to mine right now!5 rounds of dropping pH with MA and pH is a lot more stable. Still creeping up a bit but I don't want to go too far. Letting it run a little bit and will check levels in a bit.
Added a tad more CYA and CL as well. Temp is holding nicely at around 100.
And I wonder, why did I wait so long? Oh yeah, it seemed daunting and there is only so much time in a day... work, kids, dog, etc. But hey, you know me, I can't complain
Tell Me I Should Open My Hot Tub
- Thread starter Plettschner
- Start date
In this weather, 100 feels too hot. Maybe next week I'll go a little higher!
Water is pretty dialed in. Just tested it:
FC 1
CC 0
pH 7.6 (Even after about an hour of bubbling)
TA 50
CH 80 (bumping it up to about 200 now)
CYA 20-ish
Easy peasy, so far. Keeping the FC up with varying bather loads seems like it will be the only challenge.
CSI is a tad low with the low calcium. Once calcium is up to 200, I'll be good.
Water is pretty dialed in. Just tested it:
FC 1
CC 0
pH 7.6 (Even after about an hour of bubbling)
TA 50
CH 80 (bumping it up to about 200 now)
CYA 20-ish
Easy peasy, so far. Keeping the FC up with varying bather loads seems like it will be the only challenge.
CSI is a tad low with the low calcium. Once calcium is up to 200, I'll be good.
Hot tubs like ours are acrylic. Negative CSI doesn’t matter. Unless you are having issues with excessive foaming you don’t need to add calcium.
I always thought it was still good practice to keep the CSI in a safe range for the sake of metal parts in the tub, like heaters and pump parts. Same goes for a vinyl pool... no worries about plaster, but still good practice for the metal bits.
Heck, my water is soft to begin with and I add distilled water to it all the time.. from my dehumidifier in the house. Never a problem, and no foaming at all..
Last edited:
My outdoor spigot in the back that I fill from goes through the softener (well water), so CH is usually about zip out of the tap.
Without the softener and the iron-out pellets, the water smells like iron and will make for very ugly pool water. Even with the softener, it's still questionable for iron content.
CSI isn’t for metal parts. If you look at the TFP recommended levels, CH of 0-50 is acceptable and 50-550 is ideal for vinyl pools (which would apply to acrylic as well). There is a note that some metals may be affected by CH levels near zero over extended periods of time, but that is why the ideal is 50 and up. Bring it up to 50 or so on a new fill and call it good.
What Are My Ideal Pool Levels?
Use our tool to find ideal chemical levels for any swimming pool. Check TFP recommended levels on pH, free chlorine, cyanuric acid, and more.
www.troublefreepool.com
Well I may have soft water but I still have a high iron content!! And I do have an iron filter, doesn't seem like it gets it all out however, but I do have a great secondary iron filter.. the sand filter in my pool. I have gone to always filling my hut tub from my pool and have no iron problem in my hot tub whatsoever!
Good thinking. Next fill is coming out of the pool. Save some electricity not having to heat up 55 degree water and save some time starting with balanced pool water. Just have to take TA down a little.
They are nice. I have the regular type, but I wish I had the low profile type that drops the cover way down.
That's what I got is the one that sits the cover way down.. lets you see 360 degrees instead of having the cover make a wall..
I have had a lot of lifters over the years and I like this one the best.. a little pricey , but worth every penny.
I have had a lot of lifters over the years and I like this one the best.. a little pricey , but worth every penny.
I also got these to keep my cover from getting all scuffed up on the concrete pad..
And no, I have no affiliation with Boomerang, just like the cover lifter is all.
www.carefreestuff.com
And no, I have no affiliation with Boomerang, just like the cover lifter is all.
Boomerang Foot Plates
Check out the deal on Boomerang Foot Plates at carefreestuff.com
I had the same issues with my hot tub filters. There were three new filters two blue and one white. The blue filters were oily, I wiped them down but after I put them in there was a visible sheen of oil on the tub.
I'm considering this cover lifter: Cover Caddy - Cover Valet
It doesn't require drilling into cabinet and lowers cover so it's not blocking view.
It doesn't require drilling into cabinet and lowers cover so it's not blocking view.
That one just seemed a little flimsy looking when I was doing my research...
You can get the no drill option on the Boomerang also, but again pricey!!
Boomerang Freemount Base
Check out the deal on Boomerang Freemount Base at carefreestuff.com
I've installed many, many, many cover lifts, but never one of those. Not even sure it counts as a "lift". More like a cradle, like hot springs used to use.
Spa Cover Lazy Lifter - Under Mount
The Lazy Lifter Spa Cover Lift is an adjustable medium-duty lift, fitting spas 6’ to 8’ wide. Slide under plates keep the lift in place – no drilling required.
www.spadepot.com
This is the style I recommend. There are several varieties by different manufacturers, but basically the same thing.