Search
Search titles only
By:
Search titles only
By:
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Menu
Install the app
Install
Home
PoolMath
Pool School
Support TFP
Forums
New Content
Conversations
Unanswered threads
New media
Media
New media
TFP-TV
Search media
Members
Current visitors
Forum Rules
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
R
Report
RDspaguy
In The Industry
Well-known member
·
From
Cabool, Mo
Messages
1,557
Media
99
Featured content
0
Reaction score
707
Points
0
Joined
Mar 21, 2020
Last seen
Yesterday at 10:30 PM
Follow
Start conversation
Find
Find content
Find all content by RDspaguy
Find all threads by RDspaguy
Latest activity
Postings
Media
About
R
RDspaguy
replied to the thread
New Pump Seal Failure on Start-up
.
There's a reason they don't plumb them this way anymore, and I think we're learning why. The more I think the more it makes sense. Kinda...
Yesterday at 10:28 PM
R
RDspaguy
replied to the thread
New Pump Seal Failure on Start-up
.
Yes. I don't see any issue with the pump hp. (Watched video. It was slightly painful, but with a little practice and some training...
Yesterday at 10:18 PM
R
RDspaguy
replied to the thread
New Pump Seal Failure on Start-up
.
The pump in your pic connected to the heater is pump 1, which runs for filtration and heating. The old pump is 240v 5.7 amps. What is...
Saturday at 10:03 PM
R
RDspaguy
replied to the thread
New Pump Seal Failure on Start-up
.
Ok. A J-pump is a type of wet-end, not a "jet pump". They have been discontinued, but an aftermarket replacement is available, though...
Saturday at 5:51 PM
R
RDspaguy
reacted to
gunza's post
in the thread
Replaced board and pump 2 not working.
with
Like
.
I figured out the issue. Turns out you need to put the board in Test Mode using the #1 dip switch to be able to change the settings...
Friday at 11:49 AM
R
RDspaguy
replied to the thread
Replaced board and pump 2 not working.
.
Check jumper settings and fuses.
Thursday at 5:07 PM
R
RDspaguy
reacted to
bradgray's post
in the thread
Second time this has happened, male threaded part on end of filter came off and stuck in tub
with
Like
.
I agree with everything RD has suggested. But if it makes you feel better, we have also found the tall filters in those Jacuzzi tubs are...
Jun 19, 2022
R
RDspaguy
replied to the thread
Second time this has happened, male threaded part on end of filter came off and stuck in tub
.
Sounds like you're doing it right, but that rate of deterioration is not normal, and is associated with prolonged high sanitizer levels...
Jun 19, 2022
R
RDspaguy
replied to the thread
Second time this has happened, male threaded part on end of filter came off and stuck in tub
.
Are you adding chems into the filter well?
Jun 16, 2022
R
RDspaguy
replied to the thread
Second time this has happened, male threaded part on end of filter came off and stuck in tub
.
Some filters do have a removeable thread, either press-in or notched, and these can come out. It normally shouldn't be an issue to...
Jun 14, 2022
R
RDspaguy
replied to the thread
Bullfrog SWG warranty concerns
.
Then your best friend is ozone, and you want it on as much as possible.
Jun 10, 2022
R
RDspaguy
replied to the thread
Hot Tubs... Bullfrog vs Caldera (with salt system)
.
Yes! That's exactly the point! And is why they say it is a "low chlorine" system. One or two bathers in a spa will convert so much fc...
Jun 10, 2022
R
RDspaguy
reacted to
phonedave's post
in the thread
Hot Tubs... Bullfrog vs Caldera (with salt system)
with
Like
.
Here is how ozone work on a BF spa. A quantity of water is feed into a canister, that canister is flooded with ozone, the ozone...
Jun 10, 2022
R
RDspaguy
replied to the thread
Any suggestions on how to test the circuit board?
.
This! The circ pump runs 24/7 and is therefore one of the most frequently replaced parts in a Watkins spa. It wears out after a few tens...
Jun 10, 2022
R
RDspaguy
reacted to
Methuselah's post
in the thread
Any suggestions on how to test the circuit board?
with
Like
.
Welcome to the site JW! You will be exposed to 220VAC mains so must know your capabilities and be comfortable with all due cautions. I...
Jun 10, 2022
Loading…
Loading…
Loading…
Top
Bottom