Hayward 3-Way Valve Leaking on one side?

[Pkhpool]

Will the below value kit work

ATIE Neverlube Valve Cover & Shaft O-Rings Replacement Fits for Jandy/Pentair Compool 2-Way/3-Way Valves (Parts Numbers: R0487100, 1132, 192039Z, 51016200Z, O-158, O-515-KIT-9) (5 Sets) Amazon.com

These are the ones on Amazon

 

[1poolman1]

Will the below value kit work

ATIE Neverlube Valve Cover & Shaft O-Rings Replacement Fits for Jandy/Pentair Compool 2-Way/3-Way Valves (Parts Numbers: R0487100, 1132, 192039Z, 51016200Z, O-158, O-515-KIT-9) (5 Sets) Amazon.com

These are the ones on Amazon

Any O-ring set for any brand of 2 or 3-way valve will fit. They all use the same O ring sizes.

 

[Pkhpool]

Thanks

 

[Pkhpool]

Any O-ring set for any brand of 2 or 3-way valve will fit. They all use the same O ring sizes.

Thanks I’ve purchased the below with magic grease ATIE Neverlube Valve Cover & Shaft O-Rings Replacement Fits for Jandy/Pentair Compool 2-Way/3-Way Valves (Parts Numbers: R0487100, 1132, 192039Z, 51016200Z, O-158, O-515-KIT-9) (5 Sets) Amazon.com

 

[HermanTX]

Thanks I’ve purchased the below with magic grease ATIE Neverlube Valve Cover & Shaft O-Rings Replacement Fits for Jandy/Pentair Compool 2-Way/3-Way Valves (Parts Numbers: R0487100, 1132, 192039Z, 51016200Z, O-158, O-515-KIT-9) (5 Sets) Amazon.com

I have used Atie brand with good success. When you disassemble, check out the diverter valve itself to ensure there are no cuts or abrasions on the seal of the valve. You do not need to lube it. It may be worth your $$ to purchase the actual diverter valve as a backup if the original is damaged. It is most likely fine but since you are taking it all apart, it be good to have a diverter valve handy if you should need it. ATIE does sell a kit that includes the orings and the diverter valve.
Having extra orings (your kit of 5 sets) is also good. Those do need to be lubed per the advice given by others.

 

[Pkhpool]

Thanks for you advise all great thanks, any suggestions on Amazon which divert or Valve thanks and will order

 

[HermanTX]

Thanks for you advise all great thanks, any suggestions on Amazon which divert or Valve thanks and will order

Amazon.com

I have used this with good success.

 

[Pkhpool]

Thanks I just ordered it to have it on hand thanks all I’m going to jump over to my other posting on pool lights inoperable thxs

 

[1poolman1]

Thanks I just ordered it to have it on hand thanks all I’m going to jump over to my other posting on pool lights inoperable thxs

The part HermanTX referenced is for a Jandy valve. You have a Pentair Valve, according to the handle. Those parts are not the same, a Jandy diverter won't work in a Pentair valve.

 

[JamesW]

The diverter is different for the 1.5" X 2" vs. the 2" X 2.5" valve, so you need to know which valve size you have.

270056 Diverter assy. 2 & 3-Way Valve, (2–2-1/2 in.).

270075 Diverter assy. 2 & 3-Way Valve, (1-1/2–2 in.).

As I noted earlier, if you need any parts, it is usually cheaper to buy the whole valve and part it out rather than buy the individual parts.

If you only need the O-rings, then it is cheaper to just get the O-ring set in most cases.

Compool / Pentair Diverter Valve – 1-1/2" & 2" Parts - INYOPools.com

Compool / Pentair Diverter Valve – 1-1/2" & 2" - INYOpools.com has the largest selection of swimming pool and spa replacement parts with over 70,000 parts in stock. Order today and save!

www.inyopools.com

https://www.pentair.com/content/dam/extranet/nam/pentair-pool/residential/parts-sheets/diverter-valve-replacement-parts.pdf

 

[Pkhpool]

@@@ I just cancelled my order is the Pentair one on Amazon if so can you send me the link thanks

The part HermanTX referenced is for a Jandy valve. You have a Pentair Valve, according to the handle. Those parts are not the same, a Jandy diverter won't work in a Pentair valve.

 

[JamesW]

Can you verify the valve size?

 

[Pkhpool]

I have the below pictures any way to tell the value size from these or how can I measure

 

[JamesW]

The fitting will show the size on the fitting.

You can also measure the OD of the pipe.

 

[Pkhpool]

Thanks James will measure AM first pool and lots to learn but like buying a plane

 

[JamesW]

Thanks James will measure AM first pool and lots to learn but like buying a plane

This is my plane.

 

[1poolman1]

I have the below pictures any way to tell the value size from these or how can I measure

Those are 2" valves. Edit: Return valves are 1.5" and suction are 2."

 

[Pkhpool]

Thanks I ordered the below as previously in my post appreciate all your help ATIE Neverlube Valve Cover & Shaft O-Rings Replacement Fits for Jandy/Pentair Compool 2-Way/3-Way Valves (Parts Numbers: R0487100, 1132, 192039Z, 51016200Z, O-158, O-515-KIT-9) (5 Sets) Amazon.com

 

[JamesW]

The valve looks like a 1.5" X 2" valve.

Can you show the writing on the 90 degree fittings?

 

[Pkhpool]

Sorry for the delay I got sidetracked