omnilogic

Hello. I have Hayward Omnilogic with two VSP motors, a chiller, a heater, lights and a water feature. On Sunday morning the system had turned itself on running the filter at 76% and two of the regular schedules turned off. Every time I turned it off and the schedule back on within seconds it...

Hello. Dig day! What do you all think of adding an additional light to the deep end? Builder wants another $1600. Will add details on the build when I get more time.

OmniLogic question Just upgraded firmware to R4.0 at a customers house down the street in 5 minutes no problem with USB drive. I’m at another customers house now and it has been at 10% for about 20 minutes now. Any ideas? On hold with Hayward now 🥱

We have noticed that our Hayward heater in Spa mode with Set point to 98 degrees will drop down to 95-94 degrees (as reported by Omni logic) before kicking back on. Is there a way to adjust the sensitivity so that it will turn back on? In some instances we find ourselves manually toggling the...

After a lengthy search found the Hayward bubblers. Then the bad news, the bubblers are designed for a gunite pool and Hayward does not make a fiberglass/ vinyl conversion kit. Using OmniLogic automation and have the 320 lights. Looking for a bubbler that is compatible with the 320 lights. Any...

Equipment-Hayward 1.85 THP Variable Speed Pump OmniLogic automation All installed spring 2020 by previous owner/ builder. Under “Select device” I see: MSP. HUA 00-4c-07-f4-a6 version R3.2.0 MP 01-47-07-f3-f8 version R 3.0.0 MSP id 85587 (not sure what this means) Problem: CommLoss...

We are building a beachfront home and the 40'x15' pool is the centerpiece of the backyard overlooking the ocean. We are scrimping everywhere, but we don't mind spending more money on the pool... without being stupid. Our pool contractor has designed a very basic pool and we would prefer more...

Hello All, Just started putting the final touches on my new pool build. With that being said I am running into issues when I create more than one water feature in the configuration. I ran several tests and noted that when I have two water features created the tristar vs pump seems to start...

Hi all! I am looking for the possible cause and hopefully even a solution. Knowing the cause however will go a long way in me coming up with a solution. I have 4 deckjets. They are all on the same leg of plumbing. In addition, they were installed in a loop so that they all receive the same...

Hi all, I am in the middle of a pool build and is wondering if anyone has any experience with fire pits and automation. I bought a firepit ring with an electronic ignition on it and was thinking about having the electrician hook it up to omniogic rather than a switch on the wall. Is this...

Hello all. Just had my pool completed and have installed an Omnilogic control system. I have a simple standard 120v spare barn light that I would like to install over the pump. Just looking for some light for late night clean out etc. Question: Can I just hook this up to one of the spare...

Good morning. I have an OmniLogic panel and pump with a Hayward natural gas heater. The omnilogic was installed last summer, and I absolutely love it ever since I hardwired the internet connection. The issue I'm having is that the heater does not force a call for the pump to turn on. I only...

Hi all - in the four years of owning the Omnilogic i've had to calibrate the touch screen twice using the procedure found on their site -> Config -> Shell https://hayward-pool-assets.com/assets/documents/pools/pdf/troubleshooting-guides/omnilogic-how-to-guide.pdf?fromCDN=true However this year...

My salt cell stopped working and after investigating, the port where it plugs in is burnt all the way to the motherboard. Just wondering if anyone has encountered this and on

We have a Hayward OmniLogic controller for our pumps, heaters and valves. We are in middle Tennessee and we run our pool year-round, but stop hearing when night-time temps dip below the 50s. Our OmniLogic controller automatically turns our pumps on when the air temp drops below 40. However, the...

Solved

For anyone that has configured an Omnilogic, I have a question. On a new build, do I have to wait until my pool is full to power up and start configuration of the panel? I wanted to start the configuration early, but I am not sure if it is ok to do so. Does anyone know? Thanks for the help! Troy