Search results

Hi experts, I‘m getting an error 10 communication code. I checked the cable at both ends and all seems good. No corrosion at the motor connection and looked water tight still. I checked the cable with a meter and all seemed to test properly. I am suspecting the motor is the cause but does...

Yes, its correctly wired to the load side now. I turned the pump on and off to test it a few times and the SWG correctly powers up and down appropriately.

Thanks for the quick reply. It was my mistake. I was certain I wired it to the LINE side but I had it backwards. Switched the wires and all is good. Thanks again!

I wired it off the same relay as the pump and heater but for some reason the SWG is always powered on. Am I correct, the SWG should have no power until the pump comes online?

I figured as much but not concerned as I don’t mess with the chlorine output very often. Do I wire it on top of the pump wires on the same relay?

Couple of questions. I’m installing an IC40 with the iAqualink system. Is there any way these two will communicate with each other to where I can control it with my app? Or will I be running the IC40 independantly? Second, question on wiring... I’m running a Pentair Intelliflo pump with my...

I did the SLAM after. Is this a new acronym for here? I’ve been on here off and on for years but don’t recall it being called this??? I’m about 4 days into the process. Does it usually take this long?

Hi! I’ve had a few patches of yellow algae over the last few weeks. They scrubbed up with no problem. I’m in the process of super chlorinating (liquid 10%) the pool to wipe it out. The pool looks great but I’m burning through chlorine. Going from a 20ppm to 2.5ppm. I have scrubbed the pool and...

Okay, thank you everyone, its all working now! The way Dodger suggested worked! Not sure why it didn’t at first attempt.

The handle isn’t on it but I don’t believe so. I will double check to be sure. This JVA is supposed to be full open or close.

Maybe the better question is: Can I add a JVA valve to an open Aux port?

PoolGate, thanks for the reply. What would your suggestion be for the proper way to physically wire and program the valve for my deckjets?

Thanks Dodger. I tried that but no luck. I assigned the cleaner port to Aux 6 in the JVA menu. I went into the Aux menu and renamed it to “deck jets.” Just to be clear, I don’t have anything plugged physically into the Aux 6 port? The JVA is plugged into the cleaner port.

Hello, I recently upgraded my controller to the iAqualink system. Easy upgrade and everything works right out of the gate with the exception of one JVA valve. I’m having trouble setting up one of my water features. Aux 1 - activates secondary pump and sheer descent. I need to activate a JVA...

I have the Aqualink PDA system which I have it set to control my pool, spa, heater, lights, waterfall, deck jets and gas fire feature. If I upgrade to the iAqualink, will I have to reprogram all the features and valves? I’m guessing yes since it will require changing the board...at least I think...

We are ready to start tackling our buried spa (courtesy of the previous owner). From what I can gather, they just cut the pipes at the equipment pad and left them buried. The spa is just filled with rocks and dirt, then added concrete on top. Since its not a spill over spa, what is...

Mine quit working after only being installed a month. Thanks for the info and link to order the switches. Mine just went out so hopefully this works! Edit 6/24/17: it worked! Thank you!

I'm thinking of getting the IntelliPH as well. Do you control it through your EasyTouch system? Or is it stand alone? I like how you used an actual T instead of the saddle clamp. Do I only need one or two? Are there separate probes for injection of acid versus checking chemistry?

It works! Changed everything to Feature 1 and must have solved the problem. Thank you Jim and GDN for the help!

There is no change from hitting the Aux1. The pump continues at the same speed. Nothing happens when I push the button. The pump speed doesn't change and the valve doesn't move. - - - Updated - - - Is there an easier way to set a function to activate the valve and schedule it? At this point...

Hi Jim, Thanks for catching those errors. I made the changes but still not getting the actuator to turn though the panel command? Pentair has made this a very frustrating process. I appreciate the help!

Yes, the valve will change positions if I manually toggle the switch. Thank you for the suggestion. Let me power down and try changing the position of the actuator plug into the AUX A port. Also, I don't have a spa remote or a spa.

Thank you for the link! For some reason, I only noticed the Windows version originally. I have updated the protocol adapter to the latest s/w too. I must still be missing something? When I click the Aux1 button, nothing changes. Below are the screen captures of what I did. Do you see what I'm...

Thanks for the quick reply Jim. Sorry, I meant program the EasyTouch. I'm using the ET for all programming functions. I have ScreenLogic for my iphone but I'm not finding it any easier to use than the ET menu. I can't seem to find the program to download to my macbook. There doesn't seem to be...

Hi, I've read the manual and watched many youtube videos without finding what I need. I have a pool only, no spa. I have a 3-way valve going into the pump that switches from skimmer to wall suction (currently hooked to my suction creaper). I have installed the actuator on this valve. I need...

Thanks Jim! Much appreciated!

Thanks Jim for the response and appreciate the tip on the screenlogic. This is along the lines of what I was thinking. With the setup you mentioned, does the system IC60 know to activate only when the pump is running? Any special programming or does it just know?