Recent content by utell

  1. U

    Ichlor vs. Intellichlor

    Thanks. It is about 8 years old. I already replaced the flow switch a year or 2 ago. I think it just might be time to replace.
  2. U

    Ichlor vs. Intellichlor

    I have a few questions on the Ichlor. I search the forum and could not find answers. I need to replace my IC40 and I am considering the Ichol 30. I have a 19,000-gallon pool with a UV light sanitizer. Is the Ichor the latest Pentair SWG? I saw a few youtube videos saying that? Does anyone...
  3. U

    First cartridge filter flush

    I use this one. It works great. Takes less than 30 minutes to clean 4 of them. https://www.amazon.com/Mi-Way-Aquacomb-Filter-Cartridge-Cleaner/dp/B00818KY0Y
  4. U

    What have you found in the skimmer basket?

    Worse thing I found is a baby rabbit. Also had a coral snake. Sent from my iPad using Tapatalk
  5. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, I am able swap out Stenners and get the 220. I appreciated all the help. I guess I was just testing your knowledge. [emoji3][emoji106] Looks like I will be back to your original drawing. Thanks a ton for you help. Now I just have to wait for the exchange. Let me know if the...
  6. U

    Stenner Pump Wiring to EasyTouch Relays

    Thanks. I hope to work on it next weekend. I will check to see if I can swap out Stenners.
  7. U

    My WaterPots (fountains) are dry

    Jim. Got it thanks. Eventually I will figure this pool plumbing thing out.
  8. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, Thanks. I think I got it. I assume you meant upper left relay is the pump. Picture came out rotated negative 90. One question is neutral bar. Do you mean the connected group of white wires? Best, Eric
  9. U

    My WaterPots (fountains) are dry

    Thanks all. I do not think it is a leak. My valve position have not changed at all. Sounds like it might be a check valve. Where might they put a check valve? It is probably better they drain back into the pool. I now have less squirrels drinking out of them and birds playing in them I...
  10. U

    My WaterPots (fountains) are dry

    I have some water pot that are on a separate single speed pump. The pump runs these and a bubbler. They used to always have water in them however now they are always dry see the picture Running After running Could it be a leak? Sent from my iPad using Tapatalk
  11. U

    Stenner Pump Wiring to EasyTouch Relays

    Thanks. I finally was getting around to install it. However, I forgot my Itellitouch was original an EasyTouch 4 and it looks like I am missing relays. Pentair replaced it right the build due to some issues. Attached is a picture of the inside of my unit. So my question is: Do I need...
  12. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, Thanks. So can I wire an outlet into that relay grabbing power from my GFI. I prefer to leave the pump plug in place. Eric
  13. U

    Stenner Pump Wiring to EasyTouch Relays

    I have Stenner 120V, what is the way to wire to the Intelitouch panel. I assume I cannot do like the diagram because of 120v. I have the same setup as robbief00. Thanks EL
  14. U

    Water Pots are dry

    I noticed that my Water Pots that use to always have some water in them are dry. When I run them they seem to work fine. They fill up and then are bone dry the next day. They used to always have water in them. Any suggestions?
  15. U

    Cement board screws?

    I used Parex per his suggestion as well. It is simple. I got a drywall hopper for my compressor at Harbor Freight and used that to apply it. It could not have been easier. I put two coats on.