=Temperature Sensors=
Temperature sensors for Pentair, Hayward, Jandy, and other pool automation systems are
6 KB (856 words) - 00:33, 10 May 2022
...e cell to measure salinity. The sensor reading is adjusted with the water temperature coming from the flow switch.
...temperature and salinity combination. The higher the salinity and/or water temperature, the higher the performance (chlorine output).
3 KB (520 words) - 17:42, 24 October 2024
...ture and the automation control the heater operation to maintain its water temperature set point.
...EC code. The heater should be wired to always be powered on and set at max temperature.
6 KB (1,006 words) - 11:40, 31 May 2020
Do not use the heaters to maintain pool or spa water temperature below 70F.
...i_glt_fabc_D1J8XFV0F4CRBDGPNEV9?_encoding=UTF8&psc=1 Zodiac R0458600 Flame Sensor Rod Replacement for Zodiac Jandy LXi Low NOx Pool and Spa Heaters,Black]
6 KB (986 words) - 17:56, 13 July 2023
...om/product/tropicool/ TropiCool Water Chiller] in three sizes to lower the temperature of your pool. This is an alternative to evaporative cooling systems that ca
...called Turbo Boost Mode, designed to more quickly and efficiently reach a temperature set point.
7 KB (1,138 words) - 19:17, 13 December 2024
...or-assembly-apa0003/ Tri-Sensor], which detects water flow, measures water temperature, and measures water salinity.
...ct cleaner.<ref>https://www.troublefreepool.com/threads/autopilot-nano-tri-sensor.195713/post-1725528</ref>
6 KB (887 words) - 15:33, 2 January 2025
...a low voltage on/off remote connection (requires Hayward water temperature sensor sold separately)
*Inputs for water and air temperature sensors (temperature sensors sold separately)
6 KB (895 words) - 21:18, 21 December 2024
...t temperature. Note that Heat Pump BTU output and efficiency vary with air temperature and relative humidity, as shown in the table below:
...performance when the ambient air temperature is very low (when the ambient temperature drops below about 50F). This is because heat pumps do not make heat; they c
15 KB (2,315 words) - 19:46, 19 December 2024
...r, solar temperature sensor, water temperature sensor, and air temperature sensor. The TCX PIB has a switch in the center of the board to set 115V or 230V in
...PIB in a metal enclosure, the Connection Hub, a wireless light switch, two temperature sensors, and other installation parts.
7 KB (1,166 words) - 17:58, 23 March 2025
...e is upgrading to a larger heater capable of maintaining the desired water temperature in frigid conditions. A more powerful heater can compensate for heat loss t
...ition, a hot tub with a cooling feature or the ability to adjust the water temperature for cooling can enhance comfort during hot summer days, making the hot tub
6 KB (918 words) - 21:51, 27 December 2024
==Temperature Sensor==
The [[Temperature Sensors|temperature sensor]] is a standard 10K ohm thermistor.
10 KB (1,457 words) - 20:41, 4 December 2024
The cell has a built-in level sensor with LEDs to confirm it’s positioned correctly.
TruClear XL automatically reduces chlorine output at low-temperature ranges when less chlorine is needed to preserve the longevity of the salt c
11 KB (1,747 words) - 21:06, 28 April 2025
*A redesigned conductivity sensor provides more accurate salt level readings.
==What Does the Flow/Temperature Switch do on the IntelliChlor?==
27 KB (4,205 words) - 15:26, 27 March 2025
==Jandy Tri-Sensor==
The Jandy tri-sensor measures water flow, salinity, and water temperature.
26 KB (4,042 words) - 03:31, 10 April 2025
...reset and generating chlorine. We recommend turning the SWG off when water temperature drops below 60F during the winter.<ref>https://www.troublefreepool.com/thre
===RJ45+ High Water Temperature Error===
22 KB (3,485 words) - 22:03, 29 April 2025
*5 external inputs; 3 for temperature sensing, 2 for external input devices
**A water temperature sensor is required for heater operation
13 KB (1,908 words) - 22:03, 29 April 2025
...ntegrated display and control panel. The only serviceable part is the Flow-Temperature Switch (P/N 523100), which it shares with IntelliChlor and is replaceable.
...ng devices (salt test strips, electronic testers, and titration). The salt sensor reading is within +/- 300 ppm accuracy.
9 KB (1,405 words) - 23:53, 21 December 2024
The temperature Limit Switch, Exhaust Gas Temperature Limit Switch, and Vent Pressure Switch are also on the limit string.
...ple as a bad flame sensor. On the FD units, the flame sensor is a separate sensor, and sometimes, you can use steel wool or a small steel/diamond file to cle
28 KB (4,602 words) - 21:33, 22 March 2025
...m 33º F to 42º F (38ºF is the default). Go to configuration and set freeze temperature as you like. Unlock configuration by pressing < > at the same time for 10 s
...e and that the sensors are not switched (air sensor connected to the water sensor terminal).
12 KB (1,991 words) - 02:15, 6 December 2024
*Temperature rise between the inlet and outlet to optimize flow and VS pump speed
...tion, the JXiQ calculates the time it will take to heat water to a desired temperature and displays the estimate on the digital screen.
16 KB (2,630 words) - 01:52, 12 January 2025
