Search results

same for rme, less than 20

No Kidding! That great, thought I would have to drain this year, but find out I need to add some, OK cool thanks

I opened my pool today and CYA is at 20 vs 50 when I closed it for the fall. We had some heavy rain this winter so since I drained a few times I thought it would be lower, but not by this much. I also thought that CYA could ONLY be reduced by draining, but now I read the following on TFP...

I have the speedstir and love it...except, it is not very water resistant. I have had to clean out the corroded contacts or even twice resolder the connections to keep it going. Any good alternatives out there?

going away for a week so going to use pucks and floaters. I have used them in the past and they do not seem to keep up very well with the FC demand so I use two of them, even then it is kind of marginal. So I wondered if there is a formula or suggestions for how many floaters are needed for my...

OH cool, how do I do that?..nevermind I found it, I should be a bronze now

Thanks mknauss, that's about what I am adding now. It has been 2.5 years since I have had any issues with my pool water. No cloudiness, no algae, no nothin'. Thanks to the forum, and you in particular, have helped me answer all my questions. Joe

OK, thanks, so with TA of around 80 for new tap water, I should expect my PH to rise when adding water? If so, I can just add MA as needed, but since it seemed an unusually high amount, just checking nothing else was wrong. I check FC daily and CYA is 40 so I am OK there

OK measured fresh tap water and the TA is about 80. My test kits says the pools water should be 100-120 for a chlorine pool, but frankly I do not know what to do about this? I never remembered adding muriatic acid so regularly. If this is just a fundamental of my water source I guess there...

haha, I never thought to measure the TA of my fill water, duh! thanks

I only use liquid chlorine and my PH usually goes up very slowly. I usually have to adjust with Muriatic acid once a month or so. Lately it is rising very rapidly with having to add some muriatic acid weekly. I have added some water, not much, an no other chemicals, any ideas? ...or is it...

OK. Two floaters just does not seem enough for me, so got two more. Four floaters seems like a lot though :)

I use Liquid Chlorine 100% of the time...except on vacation. The floaters with tabs are OK, but I have had mixed results. What is the opinion about tabs in the skimmer if I set the pump timer to run 24/7 while gone?

yes.thanks, well aware, as I need to raise it a little right now due to some necessary pool drainage

CYA is around 40, raising it a bit now using tabs

thanks. I too keep FC in check every day, but I use a lot of chlorine (almost 1 gal per day), now I am thinking that maybe I am not using enough powder, so if you cant use too much, great, I will use more if my readings have maybe have been low

I daily use the FC powder test (R0870/871) test in 10ml water. Today I had two widely different treading, although also from two different places in the pool. One had a heaping spoonful and one use a REALY heaping spoonful (which gave the higher reading), so can you use too much powder in the...

alternatively, I could set pump to run 24/7 while on vacation and put them in skimmer?

I typically only use LC for my pool, but I am doing some testing using chlorinating tabs for future vacation times. I have a 22K gal pool with two floating chlorinators and the 3 inch tables added are broken up for quicker dissolving, even so I am only getting 2.5 ppm so having to add LQ each...

Thnaks, I am very aware of the increase in CYA, as I monitor it , and since I only use pucks when on vacation, I only need to partially drain/refill pool every few years

LC would be great, but more expensive. If I only use the chlorinators with tablets when on vacation like I do now and monitor CYA, any disadvantages to the auto feeder that use tablets?

oh I see, the tabs are no "sitting in a tub of water" to then dispense when pool pump engages, but water only runs over them when pump is on

Hmm, trying to visualize. I cannot find a good picture of a Stenner Pump , but other feeders look like they are large tanks to hold tablets than have and in/out tube for the water, with dial control for concentration. Sam idea? soem or only about $100, but is Stenner better?

OK thanks, but question on chlorine feeders like Stenner Pump. I have been told to not put pucks in skimmer due to build up when pump is off then sudden release. Wouldn't these pumps have the same issue (of course I know very little about these pumps)

since started following TFP and only use LC and maintain min levels, I have not shocked my pool since initial SLAM 2 years ago, pool water has been crystal clear all of the two years!

I have been searching, and I thought it a great business opportunity, for someone to offer service only when on vacation. I would pay many times the usual 1 month rate myself for this service, but haven't found anyone yet :)

I always use liquid chlorine (per TFP) except when on vacation. Then I use the floating dispenser with 3" tablets (and closely monitor my CYA). However, the dispensers seem too slow. I even use two floaters for a 26K gallon pool and they hardly keep up with demand. Any suggestion for faster...

Maybe it’s not The liquid chlorine that is raising my PH maybe it’s just the water in our area not sure but in any case usually a small amount of muratic acid lower back right away

My free chlorine is about 6.0. That’s funny that you say that liquid chlorine does not affect pH I have always found that liquid chlorine slowly lowers the pH and tablets slowly raise the pH. Since I generally only use liquid chlorine I have to add acid every other week or so a small amount but...

I follow all of the guidelines here and have had no issues in 1.5 years. My PH rose (which of course it does via adding liquid chlorine), but after adding significant amounts Muriatic acid (couple of pints) it is staying high via the drop test. Very odd as adding a small amount of muriatic...