Search results

From listening to everyone I am suspect that the size of overflow basin may not have been built big enough. In helping builders with building infinity pools I find this to be the biggest problem. By knowing the square footage of the pool surface, length of weir along with the depth of the...

When ever I hear about the IF code I always go to having a manometer put on the incoming and outgoing side of the gas valve for gas flow. Flow is important here not pressure. Here are the check points. Spider webs in the orifices and burners Making sure the ground on the flame sensor is...

There are four valves available for the Hayward DE filter SP0710XR50 1 1/5" threaded ports. 6 position multiport SP0715XR50 2" threaded ports 6 position multiport SP0740DE 2" glue in soc ports. 4 position Filter, Backwash, vacuum to waste and bypass. SP0410X502S 2" slide...

Patrick, I believe you spoke with Dan and John at Hayward and you are up and running.

There are three multi port valves available for the Hayward DE filter. SP0710XR50 (1/2" threaded ports, 6 position sand filter valve adapted for the DE) SP0715XR50 (2" threaded valve, 6 position sand filter valve adapted for DE) The third one is my choice unless having a threaded valve...

Check the rod as it may have unthreaded out of the tank. When you tighten the top it will not tighten completely since the you have reached the bottom of the threads on the rod.

The EcoStar is still manufactured. The drive problem was solved.

The union connector kit for the Matrix pump is a SP1500UNPAK2

To make sure it is a leak fill a bucket with water and place it on the steps in the pool. Mark the water level in the bucket and pool. If the level drops the same, evaporation, if it drops more in the pool, leak.

One more thing about cartridge filtration I do not see covered. Make sure to let the filter get dirty and rise in pressure. As the filter gets dirty it will capture smaller particles.

http://www.hayward-pool.com/pdf/manuals/UniversalColorLogicandCrystaLogic-InstallationandOperations.pdf http://www.hayward-pool.com/pdf/manuals/ColorLogic-LED-SP05xx-SPX05xx.pdf Not sure which one you have.

Someone needs to take the heater apart and expect the exchanger. Could be a baffle issue inside.

Model of our Power Flo II pump made in Europe. I have no information as I am on the US side.

I have been told that the first year or two of the Aqua Plus (15 years ago) would accept either a T5 or T15 cell. The T-5 cell is normally used on the AG Aqua Trol unit.

I am going to assume you have an SP2602VSP. 01 is DC voltage and 03 is incoming AC voltage. Could be a drive or a voltage problem. Have the rep check it out.

The current Aqua Plus is a PL-PLUS or PL PLUS-16. The current model will accept all cell types with the older models only accepting the T-15. Hayward bought Goldline about 15-20 years ago. The Goldline logo still exists on some product. To know if you unit will accept all cell types, in...

I believe I answered this same question on line at Facebook. A 2 speed pump normally has three wires running to it (plus the ground wire). One common (1-115volt leg) and two more wires that connect to the motor. The common is always hot while the other two control high and low speed...

Are these 12v or 120volt lights? Have you taken meter power readings off the wires leading to the lights?

On the discharge port of the pump is a Black and Silver label with the serial number and model number. The number you gave us is the motor number.

The Aqua Plus will do the job.

The PowerFlo LX only has 1.5" internal threads. Someone may have glued in the male part of the valve. The outside of the pump suction fitting is not a normal pipe size.

Down size the impeller.

You said Powerline, is that the right model? Can you send a picture of the complete pump together.

Fingers can last 10 years.

The RJ unit does not have a flow switch.

No one has stated if the salt level has been checked independently. I am leaning towards low salt.

I take it the front of the AquaRite reads power on and generating. If not something else may be wrong.

Sounds like low salt. Have salt tested with an alternate testing device.

Here is the manual link http://www.hayward-pool.com/pdf/manuals/AquaTrol.pdf . Filter pump not running Check that the time clock manual switch is in the "auto" (center) position or in the "on" (top) position. If in "auto", then check that the time is correct (check am/pm by using the 24 hour...

After three years make sure the shoes have not wore down. If the suction is correct, have someone take the unit apart and check the bearings on the turbine.