2 pumps stopped working but work in service mode
- Thread starter 234serenapool
- Start date
234,
The pump in the pic is an IntelliFlo pump and controlled by an RS-485 com cable.
Since the pump shows "Display Not Active" it means the pump is being controlled by your automation.
For the pump to run there needs to be a speed assigned to a circuit and then circuit needs to be on.
You can use the little 3" LCD and see what you have..
Menu, Settings, IntelliFlo, Make sure the pump type shows VS, (Do not change the pump type unless it is blank..) then make sure the Pool circuit shows some RPM.. Say about 1500 or so (Not important what it is just important that there is a speed.
Tell us what you find.
Thanks,
Jim R.
The pump in the pic is an IntelliFlo pump and controlled by an RS-485 com cable.
Since the pump shows "Display Not Active" it means the pump is being controlled by your automation.
For the pump to run there needs to be a speed assigned to a circuit and then circuit needs to be on.
You can use the little 3" LCD and see what you have..
Menu, Settings, IntelliFlo, Make sure the pump type shows VS, (Do not change the pump type unless it is blank..) then make sure the Pool circuit shows some RPM.. Say about 1500 or so (Not important what it is just important that there is a speed.
Tell us what you find.
Thanks,
Jim R.
The pump is turning on and off every couple of minutes.
I have a phone app with pentair sl config
I have a phone app with pentair sl config
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
Sounds like an intermittent rs485 connection. Check the data cable at the pump end for corrosion. Also Check the data cable for a abrasion
I checked the cord nothing. I just replaced the drive on the 3 hp pump today and just can not get the programing right.
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
Aha! While in service mode, did you go into the pump settings and assign an address?
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
When you install the new drive you need to set ot up to talk to your automation.
Assign a Pump Address for Pentair Intelliflo Variable Speed Pool ... - YouTube
Assign a Pump Address for Pentair Intelliflo Variable Speed Pool ... - YouTube
So maybe I need to set this pump address to 2 since it is the waterfall pump. I set it in sl config but maybe not on the pump. I just saw a video on address.
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
That would make sense. By not addressing the new drive you likely had 2 pumps arguing on address 1
You were right, that is awesome pump 2 works great, has not worked in a year.
Now pump 1 main pump does not work. I did take the power off of relay 1. I wired the 2 pumps directly and removed power to the 1st relay and ran it to pump 1. Would that stop the pump from turning on?
I thought it would just not power the SWG.
Now pump 1 main pump does not work. I did take the power off of relay 1. I wired the 2 pumps directly and removed power to the 1st relay and ran it to pump 1. Would that stop the pump from turning on?
I thought it would just not power the SWG.
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
Are both pumps intelliflo pumps with the data cable connected?
The screens you posted earlier showed no comms on pump 1, had you changed the settings trying to get the other working?
The screens you posted earlier showed no comms on pump 1, had you changed the settings trying to get the other working?
Ahultin
Bronze Supporter
- Aug 19, 2021
- 1,602
- Pool Size
- 17700
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
While you are at it, both pumps should be on gfci breakers for safety.
Siemens QF220A QF220 Ground Fault Circuit Interrupter, 20 Amp, 2 Pole, 120 Volt, 10,000 AIC, Color https://a.co/d/cpwSvH8
Siemens QF220A QF220 Ground Fault Circuit Interrupter, 20 Amp, 2 Pole, 120 Volt, 10,000 AIC, Color https://a.co/d/cpwSvH8
Just ordered the GFC, thanks the builder did not put them on.
I was able to fix both pumps thanks
Similar threads
