resilience chlorine generator Model: 305PX

[tpm]

Hello all
a couple of days ago after vacuuming the pool I noticed my Hayward heat pump along with my Resilience chlorine generator Model: 305PX has stopped working. Heat pump has LP error which may be water flow issue. The salt generator has a blank screen ( direct wired to outside circuit panel and panel has power ). None of the controls work. Power, mode, etc. would this have a fuse somewhere to check? I turned off main pool breaker in house for several hours, i backwashed the pool but no help. After vacuuming the pool there was a lot of air in system that I purge.
any ideas?

Thank you

 

[ajw22]

I believe this is your SWG manual - http://edc.poolsupplyworld.com/wpdf/nexa_pure-installation_manual.pdf

Do you have a multimeter to check the voltage at the power connection shown on page 9 or 10?

Is your SWG wired through a timer?

What model filter do you have? When was the last time you backwashed or cleaned your filter?

Routine Pump/Filter Maintenance

A working Filter and pump are vital parts for your pool. Read our artiticle on how to clean your filter & other Pool Maintenance Tips.

www.troublefreepool.com

Tom, please creating your signature with details of your pool and equipment.

 

[tpm]

Hello
Yes it is wired with a timer, goes on when pump goes on. I also have a Hayward DE filter that was NOT in need of a backwash but I did do one after this problem. Didn’t help. And really not good with using a multimeter although I do have one

 

[Dirk]

Hi Tom! Allen is asking you to provide more information about your pool so he can better answer your questions. Here's how:

Create Your Signature - Further Reading

www.troublefreepool.com

 

[ajw22]

Checking power through the timer with the multimeter is the next step.

What timer do you have?

Post pics of your equipment, timer, and SWG.

 

[tpm]

Checking power through the timer with the multimeter is the next step.

What timer do you have?

Post pics of your equipment, timer, and SWG.

Will do that today. My Hayward heat pump went out along with it. Not sure how connected to the salt generator other than possible low water flow

 

[tpm]

Hi Tom! Allen is asking you to provide more information about your pool so he can better answer your questions. Here's how:

Create Your Signature - Further Reading

www.troublefreepool.com

I'll try to do that today

 

[tpm]

34,000 gallon L shape with water feature on separate pump

Pump. hayward sp2610x15. 1.5 hp

Hayward DE filter. DE 6020

Hayward HeatPro heat pump

HP21404T

140,000 btu

Resilience Salt Generator.

 

[Dirk]

Excellent! Thanks Tom. Uh, I just realized we're calling you Tom. Did you actually tell us your name!?! Maybe Allen knows you from your other posts. Good luck with the troubleshooting...
Beautiful pool and yard, by the way!!

 

[tpm]

Excellent! Thanks Tom. Uh, I just realized we're calling you Tom. Did you actually tell us your name!?! Maybe Allen knows you from your other posts. Good luck with the troubleshooting...
Beautiful pool and yard, by the way!!

Thanks, Lol. Yes Tom is good ( although I’ve been called much worse )

 

[ajw22]

You are back to tracing the power through the timer to the SWG with your mutimeter or getting someone who can do that.

 

[tpm]

You are back to tracing the power through the timer to the SWG with your mutimeter or getting someone who can do that.

I’ll need to find someone to do it unfortunately. It’s only 2-3 years old, same as the heater

 

[tpm]

So I found I definitely have power going to the salt gen. I even disconnected the cell to see if an error would come up but nothing . Possibly the circuit board is bad?

 

[ajw22]

How old is the SWG?

What does a new board cost versus a new SWG unit?

 

[tpm]

SWG is only 3 years old but unable to find parts for it

 

[ajw22]

Replace it with a new unit. Hayward Aquarite or Circupool.

 

[tpm]

Easy if I had an extra 13-1400.00

 

[ajw22]

Open up the SWG and post pics of what the boards look like.

 

[tpm]

Open up the SWG and post pics of what the boards look like.

I will but may need to wait a couple of days. I’ll be out of town

 

[tpm]

I was able to grab some pictures before leaving
green circuit board with ribbon is for display