Anyone know who has them in stock? Inyo is shipping you CMP valves, Polytec site is down. Looks like InTheSwim may have them, but I'm suspicious if they really are.
Jandy Diverters In Stock?
- Thread starter Plettschner
- Start date
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
it sure is...
You could use 2, 4716 and have way better control than a 3 way valve.. I went to all 2 way valves for my new pool setup.. cost more but way better control over every single connection...
You could use 2, 4716 and have way better control than a 3 way valve.. I went to all 2 way valves for my new pool setup.. cost more but way better control over every single connection...
Jandy 2-Way Never Lube Valve, 2" - 2.5"
www.polytecpools.com
You like spending my money, don't you?
One is for my heater bypass, the other is for skimmer/main drain control... I could use a 4715 (1.5" incoming from skimmer and drain) or a set of 2-ways on the suction side.
One is for my heater bypass, the other is for skimmer/main drain control... I could use a 4715 (1.5" incoming from skimmer and drain) or a set of 2-ways on the suction side.
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
Not that I like it but you know
Ahh, you really need a 3 way for the heater, is your pipe 2 inch? you could also use the 1.5 / 2inch Part # 4715, they have that one in stock...
Ahh, you really need a 3 way for the heater, is your pipe 2 inch? you could also use the 1.5 / 2inch Part # 4715, they have that one in stock...
Pipes to/from pool are all 1.5" but I'm redoing pad in all 2" looking towards the future. I could do the 4715 valves... though I was shooting for an "all slip and no couplers" install. I'm probably being ridiculous.Not that I like it but you know
Ahh, you really need a 3 way for the heater, is your pipe 2 inch? you could also use the 1.5 / 2inch Part # 4715, they have that one in stock...
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
with the 4715 it is still a slip it is just on the outside of it instead of the inside, using the outside is actually better...
From what I learned, and I'm no plumber or pool pro, the 1.5" slips into the 4715 where the 2" butts up to it and requires a coupler (or ell, or tee) fitting to connect to the 4715. In other words, the ID slips over 1.5" pipe and the OD is the same as 2" pipe.
The ID of the 4715 is close to the ID of 2" pipe, but there's also the reduced diameter of the stop lip for the 1.5" pipe. I have to think the 4717 is going to be less restrictive being that it's designed for 2" pipe to slip into it.
I could very well be wrong in my assumptions.
The ID of the 4715 is close to the ID of 2" pipe, but there's also the reduced diameter of the stop lip for the 1.5" pipe. I have to think the 4717 is going to be less restrictive being that it's designed for 2" pipe to slip into it.
I could very well be wrong in my assumptions.
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
I am not sure of that.. I have always used the inside and I "thought" you know how that goes, that the outside was for the 2 inch...
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
you are correct... I just measured my 4724 1.5 and 2 inch valve.. 1.5 inch inside and the outside is a 2 inch pipe that would need a connector... You can see below, the inner size is exactly 1.900 and the outside is 2.375 using my caliper to measure... ..
- Apr 10, 2018
- 6,426
- Pool Size
- 18375
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
I picked some up from this place in March. There's no indication as to whether the parts on in stock, so you'll have to call for availability.
Good luck!
www.poolsupplyunlimited.com
Good luck!
Jandy Pro Series Neverlube 2"x2.5" Positive Seal 3-Port Valve | 4717
The Jandy NeverLube 4717 valve is totally maintenance free and built from the toughest CPVC material that can withstand extreme chemical and temperature fluctuations without ever leaking, cracking, or breaking.
www.poolsupplyunlimited.com
Thanks! I tried... they're back ordered at PSUI picked some up from this place in March. There's no indication as to whether the parts on in stock, so you'll have to call for availability.
Good luck!
Jandy Pro Series Neverlube 2"x2.5" Positive Seal 3-Port Valve | 4717
The Jandy NeverLube 4717 valve is totally maintenance free and built from the toughest CPVC material that can withstand extreme chemical and temperature fluctuations without ever leaking, cracking, or breaking.
- Apr 10, 2018
- 6,426
- Pool Size
- 18375
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
I figured...hope you find 'em.Thanks! I tried... they're back ordered at PSU
- Jul 3, 2013
- 9,027
- Pool Size
- 15000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool SJ-40
Similar threads
