wifi

I have an outdoor pool timer from Dewenwils (a T30) that has worked reliably for a couple of years. The unit has one recurring problem. Any change to the WiFi requires re-pairing the T30 to the WiFi. Usually, I can get this to work after 10 to 25 attempts. No luck this time. The T30 is quite...

This is my first post, but a long time reader and lurker. I wanted to replace my controller on my HotSpring Spa since it had finally gave out after almost 20 years of service and getting a new IQ2020 controller is just to expensive for what it does and the lack of any kind of integrations or...

Hello all, we recently completed a pool that has an intellicenter panel with the Wi-Fi link kit. The customer has reached out twice over the panel loosing its internet connection after a power outage. Once during a thunderstorm and again when Generac was installing a home standby generator. I...

I found a WiFi enabled outdoor timer with two independent circuits, and it runs on 240vac so I don't have to have a neutral in the box anymore. I got the Suraielec WiFi Pool Timer and installed it today replacing the old big wheel Intermatic switch. I wired it so the relay feeding the SWG isn't...

Howdy! I have the old school Easy Touch automation (converted from Compool) inside of a metal control panel box. I don’t want to waste $500 on the terrible Pentair wifi/app, and instead I want to try running this amazing Nodejs-pool controller project I just learned about on a Raspberry Pi...

I came across this: Add water to the pool automatically and since it was an old thread I started a new one. I did something similar to this post but added a simple way to make it automatic. If you estimate or actually measure the rate of water evaporation (measure inches of water level lost in...

Hey there, I have a current setup of two switches - one for pump and one for heater. Everything’s on 240v. Looking to automate with the WiFi timer and just want to make sure wiring is correct.

Hello, I’ve connected the WiFi kit to my intellicenter control panel. I followed the directions (which are quite confusing) and I’m getting the following errors shown in the photos provided. It should be noted that I assume I did everything correctly because my panel says I am connected to the...

I have searched for a few days with different terms but cannot find a solution for my specific situation. TFP seems like the best place for me to ask since I've tried out some things I found here. I have reached out to Polaris/Zodiac/Fluidra support for the cleaner and the iAquaLink app but am...

So I wanted to share with TFP crowd my new favorite automation added to my pool system. I found out about this when trying to locate a replacement for the spa control that is unreadable and partially working , an old SPALINK® RS 8-FUNCTION. So when searching on Ebay for a lower priced unit I...

Hi all, I'm wondering if anyone might be able to help me. I currently have an old Intermatic Pool Pump timer and purchased a Suraielec Smart Wifi Timer Switch. After spending and a bit amount of time looking over the instructions and wiring diagram I'm a little stumped. Right now, we have a...

I upgraded my pool automation from the Pentair Legacy Easytouch board to the Pentair Intellicenter board. I'm able to get my Pentair VSP pump partically working. I can't get it to bump up to a faster speed for when I set a schedule for the cleaner. It is my understanding that you can overlap...

I currently have a very outdated controller, AquaLogic. Like everyone else who has or had this system it hardly ever keeps time or looses 8 hours of time then becomes non existent. Without replacing the entire system at the moment is it possible to wire in a Wifi switch to just the filter pump...

I am looking for a way to monitor how high the water level is in my pool. Ideally I'd like some kind of wifi monitor that can tell me how high/low my water level is, so I can decide if I want to add more water. I dont need an automatic filler, just something that can remotely tell me the...

I received a message from a client mentioning a lack of remote access to their automation. So far I have made an attempt to login (via Android Screenlogic Connect) and received a result of a spinning wheel and window with the text of "Login failed. Please check: Password Wifi or cellular data is...

I have just installed the Intellicenter for my pool controls and I am trying to get the wifi connected to the internet. I was able to go to connect to a wireless network and was able to see my network connection and input the password. Once the antenna reboots I go to the internet connection...

Hi all I have an intellicenter bundled with the WiFi module. I’ve tried multiple Ethernet cables between the board/power module and between power module/antenna (to the poe port). I’ve tried to reseat the power cable from both ends. The lights on the Ethernet ports never light up. When I go to...