jandy

Hello, TFP! About four months ago, my pool light started going out and would only display in red and white. The spa light still works as expected. At this point, the light simply no longer works and I have not yet been able to get Jandy to warranty it, because I bought my home with the pool...

Hello Friends!, I can call you that because you have worked us through several issues over the past 12 months. With a fast approaching spring we are in need to replace one of our pool pumps. We converted this summer to the As the previous owners broke the handheld unit. We now need to...

Hello all, I have an Aqualink RS + PDA + Aquapure installation that was already in place when I bought this house in 2009. A week ago the PDA would not respond to its ON button -- no backlight, no text on screen. I changed the batteries, but the problem remained. Troubleshooting instructions say...

Howdy all, I'm looking for options on replacing a pool pump. My pump motor started making a squealing noise last Friday (only when running higher RPM). I figured the bearing was going out and was going to schedule service after the New Year (pool company was closed for the holiday). It...

Hello I have a zodiac pump which uses the Jandy rs485 protocol. I want to throw away the controller and control the VSP pump directly from a home automation system and read back the RPM and power. There are heaps of old threads on this topic refering to the Jandy pump protocol which someone...

Hello the board: My wife and I recently purchased our 1st and last pool home! It has been a learning experience to say the least and no amount of reading can prepare you for the onslaught of data! With that said we are still 100% happy we took the plunge and are eager to learn everything that...

So I've had this pool for about 10 years now and I am fed up with the Jandy Aquapure system. It is cool to adjust the percentage from my phone, but I realize that I only really do that twice a year to swap seasons. And the cell just has problems, the first couple years it was all about the...

I spoke with Jandy by email they have confirmed that it is possible, BUT wont give me instructions only dealers of their products.... Our existing handheld which was on our old controller is Handheld 3.0 Blue Jandy PDA (Blue One) The JBox has a V3.0 sticker the board says 4606. When both the...

My Jandy VSFLOPRO pump is making a noise with leaks near the motor/wet area. Anybody in the area familiar with any pump repair service companies/tech. Please let me know. Thanks!

Hi all - brand new pool owner, so go easy on me... We have a CoverPools cover and a Jandy/iAqualink control setup. We have the Jandy-CoverPools module set up so that we can have automatic disabling of features that would floor the cover when it's closed... We now have a shutoff via a...

Hello, My heater is not working. I've replaced the flue temp sensorm I saw another recent thread about this, and I was hoping to get more insight into what to do now. I have noticed there is water on the floor of the heater and on the concrete pad surrounding it. Does this mean I need a new...

Met some problems with my Jandy automation. I have Pool and SPA. ISSUES: No lights at indoor panel. No any response when I switched to auto side on outdoor panel. (Pumps can work when I switch to manual) STEP 1: I checked and found fuse burst. Changed new fuse and burst again. STEP 2: I...

Hey y'all - second summer with my pool, was finally getting into the swing of things, had to have a pretty decent amount of cement work done a couple of months ago and a lot of the dust got into the pool... In retrospect I should have put the filter on waste but had it just set to filter...

Has anyone successfully gotten the iAquaLink 3.0 Controller to read and change the pump speed of a Pentair Superflo VST pump?

Inground pool light

This was just installed 6 months ago and has been working 100. A week ago I got a new saltcell since then nothing. I reset the IAquaLink, reconnected it to my WI-FI, logged into my security, verified it was connected and online! went to the computer logged in to the IAquaLink site and it has a...

Is there any concern going with a heater bypass (Jandy Diverter, Check Valve, Actuator) vs the Versaflo system? I've read a few conflicting threads and was hoping to consolidate the answer into this thread for future readers. Heater Bypass - Further Reading here. From the following thread, it...

Hi. have you seen this. I got a 123 error code on my jandy salt system. I pulled the wire off my jandy Plc1400 chlorine generator. The middle of the connector was melted and the middle terminal on the plc1400 looked corroded or melted. See pics. Just the middle one. At this point I’ve replaced...

Hi there. I have a Jandy Aquapure system with a 1400 cell. Recently, my sensor start reading erratic values. I tested water manually with a TSD tester and salt test strips and read a level of 3.1. The jandy said 4.2 so i did the calibration procedure(held salinity button for 15 seconds) and...

Hi All - New to the forum, but I'm already learning a lot. Sorry to post yet another jandy i-aqualink question, but they make it so difficult! We are first time pool owners. We purchased the house last November with a in-ground pool controlled by the jandy aqualink system with PDA. I'm...

I have a Jandy salt system and the up and down arrow buttons work, but the power, back, and select buttons do not. Any suggestions?

I recently upgraded my 20+ Jandy JI8000 to an Aqualink RS. That went great. This year one of the relays stopped working for my main pump. I have it working with my spa relay, but I will be changing the relay. When I upgraded the Jandy unit, I did not change the relays. They are a different...

I used this for about 3 months before getting a heat pump.I'm in the DFW area. The heater is in brand new condition and still under warranty. It is 400K BTU for propane gas.I'm asking $2k for it. It retails for over $4k Please call or text me if interested 214-675-8244 Thank you,

guys i have 3 leaking old style Jandy 3 port valves - please suggest how to re-plumb 3 new returns from SWG - I currently have SPA Return, Pool Return and Pool Drain Return as well : Didn't realize i had Pool Drain Return until recently. I want to buy 3 new NeverLube valves and replace the old...

So the Jandy valves use positive pressure, as in the water pressure pushes the flapper inside into the opening and helps with the seal. Did the install yesterday and then realized I have them both pointing with water flow into the heater, so I was like I have to turn it around when I have a...

Recently had a “ Fault - High Flue” error on my Jandy JXI , bought a new Flue sensor and installed it. Error wouldn’t clear so i cleared it out by holding pool, menu, spa button for 7 seconds, go to load defaults , finished , error cleared. Manually verify heater starts up no errors and runs for...

My pump (Jandy 2.7HP Variable Speed Model# VSSHP270AUT) has started making a cracking noise. The noise is coming from the motor side and NOT the pump side. So it can't be the impeller. Please click on the following link with audio/video: https://photos.app.goo.gl/VhY4bohJRmcCWNCy5 What do you...

2008-ish model. The High Limit Switchs are bad and had corrupted the Controller Power Interface PCB and possibly the Ignition Control. I can find "Teledyne Laars Jandy Parts" on Parts4heating but major concern is the are aftermarket parts and not "Genuine Jandy". To spend $1000 dollars for...

I found this forum too late and my pool was installed last week. First time pool owner in Indiana, we installed an imagine 10x26 fiberglass pool 5ft deep (~10,000 gallons) and automatic pool cover (under track). The decking will be techo block. The PB put in a Jandy 1.85 hp vs pump, cs 200...

I was looking over my pool quote and the equipment install. The quote says •Jandy 2.5HP Variable speed pump •Jandy 1HP Booster pump It's a 33x14 pool with a 7x8 standalone spa. But all I see is a 2.7hp vsp pump. Please look attached photo and tell me what you see.