easytouch

Hello all, and thank you for the wealth of info on this site. I've searched and searched, and read numerous threads, but want to get others' input before I buy a new Easytouch motherboard. Symptom - Heater won't power up while trying to use automation (Easytouch panel or screen logic app)...

Looking to replace logic board 521107 After lightning strike. It can be a used complete unit from which I could take out the board. For some reason Pentair doesn’t have it in the market anymore. If anybody knows where I could get one please Let me know asap. Thanks.

Hi there. You all were able to help me once before so I’m hoping you can help again. I have a Pentair easy touch automation panel. We use a remote control to switch our pool from the swim out spa to the regular jets and back. The remote control reroutes everything based on a valve. When we used...

Hi all, I added a new pump schedule via the SL Config app and the Screen logic app in an effort to have the pool pump run 24/7. I used Aux 3 for the new pump configuration and labeled it as "Low Speed" to have the the pump run at 1300rpm when the "Pool" and "High Speed" scenarios are not on...

I recently bought a home with a very nice pool with all Pentair equipment. I will add a list of what I see and some pictures to this post. I could really use some help figuring out what I have here and how to operate it all. Many of the functions in ScreenLogic don't work as I would expect, very...

I have the Pentair UltraTemp Heat pump. If I turn it on when the pool pump is not running, nothin happens! I need to turn on the pool pump to eat the heat pump to start up! Is there a way to program the EasyTouch system to automatically turn on the pool pump when you turn on the heat pump?

I would like to add a physical button or switch for my waterfall pump. It runs off of an aux circuit and is angaged through the ScreenLogic phone app. Would be nice to have a button near the pool anyone could hit to run it on. Does anyone know how to add a switch like this to toggle a relay...

I have a pool w/ spa and a single-pump (variable flow) system w/ a heater. There is a single light in the pool and a single light in the spa. I have a Pentair EasyTouch 4-function/relay control center (ET4) w/ the large (40k?) salt-water chlorinator, the ScreenLogic add-on (not sure if it is...

Howdy! I have an Easytouch panel without the app so the interface is challenging. I have a Pentair Mastertemp Heater hooked up to the control panel. Right now, I have a daily schedule where the pool pump runs 10 hours over night without the pump. I have a new situation where I need the pool...

Hey everyone, I have a Compool 3600 system controlling a pool and spa, that I want to upgrade to be able to control it from my phone when I'm away. I've been doing research, and it seems that, if I want to stay within Pentair, I can either upgrade to the Easytouch system with the Screenlogic2...

My pool builder set my pool and spa up as 2 separate bodies of water. They both have their own filters, Mastertemps, IC40s, Pumps, ect. But they share 1 easy-touch panel. He also installed 2 intellichem systems. My pool intellichem is wired into the easytouch and the IC40 is connected to the...

Hello all, I'm having some issues with my pool light, and was hoping someone here might have seen something like this and could suggest a fix. I may have to call someone to come out, but... thought I'd try here first. I control my pool with an EasyTouch remote. I'm not really sure what version...

I have a few extra omron relays for my compool et upgrade setup. I use a Jacuzzi JSCS-40 on AUX7 so I can schedule its startup and shutdown (usually 1/2 hour after the pump is scheduled to start and before shutdown). Im thinking of introducing a flow switch on the low voltage side, basically...

Intellchem hooked up to the Pentair Acid Pump and an IC40 SWG. All settings look good (Relay 2/ICHLOR) When intellchem says it's dosing, nothing happens at the Stenner pump, no movement, noise, nothing. Tried switching to a different pump (I had a chlorine pump that I won't be using) same...

I'm looking to upgrade my EasyTouch 4PSC-IC20 with the intellicenter upgarde. My Easytouch is a single body (Pentair #520592) w/ SWG integration. Based on my research It looks like I'd use the upgrade kit# 522047 for single body systems. I'm looking at adding a hot tub next year and was...

I am a first time pool owner and have a question about the wiring and programming of my Pentair VSF filter pump with an EasyTouch system. I think my pool builder made a mistake and wired my VSF filter to the load side. This meant the pump wasn't getting power unless the filter relay was...

We have a vacation home with a Pentair EasyTouch pool & spa that we also rent out as a vacation rental. The controller set up has been giving us and our guests a lot of headache. Any suggestions for a pool controller system that would let us do the following? - Guests only have access to spa...

So it’s going to be a chilly night tonight (low 30’s F which is cold here in the desert southwest) and I have this great idea to heat up the hot tub, turn off the lights, and watch the Geminids meteor shower from the cozy warmth of the hot tub. But its likely that the EasyTouch’s freeze mode...

Hello, I need some help. I have an IC40 that’s connected to an Pentair Easytouch. My IC40 will only generate chlorine when I run the Super chlorinate feature. Does anyone know why? It calculates the PPM and the flow light turns on but the Cell light only turns on when i run the Super chlorinate...

Hi, everything’s been working fine this summer but today my pool guy put the system into Service mode and it won’t come out. Pressing the “mode” button does nothing (normally it toggles between Auto and Service). In fact, pressing any button does nothing. We tried shutting the power off but it...

Hi! I moved into a home that has a Pentair EasyTouch 8 system. I have tried to watch videos on youtube to bring myself up to speed on how to use it. Regarding the pool & spa lights, we have installed color-changing LED lights. Many of the videos I have watched give you the option to...

Since I replaced my Pentair Intelliflo pump, the communication will cease between the pump and my easy touch panel. They will talk and work fine together for a few days and then all communication stops. After I cut the power to both the panel and pump, let sit for about 5 minutes and turn back...

I've read through quite a few posts posts on this topic, but still cannot definitively determine what is or isn't in my EasyTouch box. I would like to convert my pool to salt by installing an IC60. I wasn't sure that I wanted salt water when the pool was under construction, but I instructed the...

New pool, first time post, thanks in advance. I just had pool/spa redesigned with all new Pentair equipment; EasyTouch4, Intelliflo VSF, Mastertemp 400, Intellichlor IC40, two Hayward PSVs. I wanted my pool contractor to add a Spa Low feature circuit but nothing he has tried works; the valves...

When I power the controller on, the panel displays correctly. If I quickly press the F-Filter Pump button it clicks and lights Red, same for control buttons. i.e. they work properly. However within maybe 10 seconds it clicks off again and the panel display gradually fades to display nothing...

Per the Mastertemp Installation instruction: ”The filter pump should run continuously when the heater is on, and for at least 5 minutes after the heater turns off. Any switches in the pump circuit (including circuit breakers) that can disconnect the pump must also disconnect the heater.” I...

I am about to install the Pentair 521107 Easytouch upgrade for my current Compool LX3800 system. I was wondering if any of the experts or those experienced with this upgrade have come into this. Sigle Body System: First of all, when I reviewed the installation instructions, the first thing I...

[UPDATE] The Pentair single-body EasyTouch system will operate a spa w 2 valves, see below. Hi, I have a pool with attached spa, incl. an actuator valve for both inlet and outlet lines. I just replaced my flaky unit with one for single-body systems. the valves don't move when I hit spa mode on...

Hello all, new to the forum and appreciate all the information here. Hoping this hasn't been covered as I couldn't find a topic similar. 15K Pool Pentair Easy Touch PL4 contoller Pentair Mastertemp 400 Heater Glacier Chiller No SPA My PB set up the automation and was probably less familiar...

Hi, everyone. Thanks for the great community! I've been learning a lot over the past couple of weeks. We had an electricity surge that fried a bunch of stuff, including my Pentair EasyTouch controller. The controller will still turn on my main pump and the overflow pump, but it won't turn...