Search results

my old pump was seized and it was replaced it with a new 011 028. keeping the old wet end in case the new one cracks. now to finally figure out how to program this thing. i can NOT create one program to change speed during the day. rather i have to create several schedules - one for 24 hours at...

to be clear - you want me to test that the circuit breaker in the panel lost a phase? or that a circuit on the pump has lost a phase?

will do. so open the connection box on the side and test the leads?

this year is the first time i have encountered this error. it had been running fine for all the years. i tried several times after reset and the pump won't start this year.

repair or replace? replace just pump or whole basket unit?

i used the drain king from the pump and water came out of drain - but nothing else. spa drain is about 10 feet from the valve and another 20 feet to the pump. but flow was fine until the drain covers broke sometime this summer. i have found a baltimore company (Excalibur Leak Detection) that can...

i have a similar device - should i try to blow from the pump or from the drain? seems like scoping or snaking would have top be from the drain - otherwise i'd have to navigate the jandy drain valve.

as winter approaches i close off my pool but keep my connected hot tub running. this year the old drain covers - dual drains - in the hot tub broke and some pieces got sucked into the pipe to the point that i can not get the pump to prime when only pulling water from the hot tub. i found a...

thanks. i guess i will start timing cycles to make sure its working. after super is done...

is the firmware the r diagnostics reading?

latest update: i like the transparent blue housing because i can see the gas being released during generation. but find it frustrating when there are no bubbles. i switch it to super and the bubbles reappear. i run my pump 24x7x365 and historically set the swg at 25P. how do i confirm that it...

made any progress? i replaced my unitherm governor is this what you mean by "pressure valve spring"? or do you meant these springs? mine was severely corroded after just 2+ years of use. and the heater now starts and runs but shuts off before set point with "hi limit 2" error followed by "no...

left the new cell in and changed to t-15. and its been chlorinating for hours. yea! here are the cells - the new one doesn't have much in the way of markings - but from the purchase receipt it in april 2017 when i thought my original cell was dying early. pool was converted to swg midsummer...

what would cause the setup to change to t-3 AL-1? is that the power outage reset?

so it should have been AL-0 for the original cell? why do i need to re-install the original cell to set to t-15? and the AL indicates the brand of cell? mine says AL-1 are you saming it should be AL-3? and what would running a t-15 swimpure with the machine set to t-3 and naturesoft do the the...

but the original cell was t-15. are you saying that the guy who installed it set it up wrong? i didn't learned about calibrating until this year.

does it make a difference? i don't see a flow direction indicator on the cell. cell is reversable.

clean de filter (running fiber) @2750 rpm is ~10psi. its at 14 psi right now. but i can start the heater and it runs until hi limit 2 fault. everytime. if i don't turn it off sometimes it will restart after it "cools off". most of the time i take what heat i can get and turn it off to save the...

with original swim pure plus t-15 auto: check salt lit, inspect cell lit,400,84,31.4,0.00,33p,0,AL-1,r 1.59,t-3 off: 400,84,31.4,0.00,35p,0 off one minute than auto: 400,84,31.4,0.28,33p,500 tested salt - 16 drops = 3200 installed 3 year old compupool Platinum Edition Replacement Salt Cell for...

how did you test the cell?

K-1766 drop test kit. salt has been confirmed by pool tech. who said i had too much flow. salt is good. or at least not as low as the 500 or 300 reading i get with the old cell. on inspection cell looks fine - no noticable scale.

flow is steady. what would cause an intermittent flow? when i turn the pentair variable speed pump down i get sw open, turn it back up and it goes away.

Moved from here. similar problem. salt is fine ~3000 depending on rainfall. my hayward aquarite with t-15 cell seems to have died. getting low salt warning and amp reading of 0-0.3 with original cell. replaced with compupool t-15 cell i bought a couple years ago. it gives me hi salt warning and...

both hi limit sensors show 2k ohm. new replacement shows 3k ohm. haven't chagned anything yet. but still getting hi limit 2 followed by no pilot sensed. intermittently. it seems some days it hits the limit at 87 on the way to 96. sometimes it gets all the way to set point and cycles on as needed...

and how come the diagram on 47 for polymer header prior to 10/2019 shows both as 1C?