Search results

Might have some firewalls blocking… PW has no special characters… I’ll call support. Thanks

Allen, thank you... I've read through and executed the above tasks, but still no Remote Connection ablity... I say that because I'm attempting to login via the Pentair IntelliCenter App on my phone with NO-Wi-Fi on - - thus, emulating a "remote connection." I can still login with the App when...

I recently upgraded my EasyTouch-8 to Intellicenter-8 panel. Love the interface and have learned the in's and out's of Circuits & Features [thanks to Jim and others]. However, I'm having trouble "Remote Logging In". No problem with Local Login [WAN], but Remote is N/A... I have the following...

I purchased and installed a refurbished motor for $160. It’s been working great for 5-days. Going to commit to removing from pool when not in use. Hopefully helps it last longer!! Shannon

Greetings, long time no post... I've got a 2.5yr old Maytronics E30. Just did a gear/wheel-bearing overhaul last month and all was working great. Now, the it turns off after about 25-seconds in the pool. 1. The controller stays on 2. I can take the E30 out of the pool, run it in test mode...

Gotcha... I already have EasyTouch, and my PB is contracted out to get me Intellicenter; says he has it; but is MIA - - these PB's... man-o-man!!

Where did you source the Intellicenter? Thanks, Shannon

This has been fixed by chipping out a small section of my plaster; reinstalling the correct Return; and replastering... Now, I just need 4 more of these little boogers [Threaded Microbrite Light Adaptor], as my PB's assistant cut them off a few months ago... And, now PB is MIA... Anyone have...

So, my PB's "helper" cut off some of my Microbrite Threaded Adaptors, and was hoping someone on this forum may point me to a source for them? Retail / Distributor / Installer / ?? My PB has been MIA for a few months, and I'm getting tired of waiting for him to "come through" with these...

There’s no good solution short of draining the water below the lights; chipping away some plaster; placing 1.5” slip on pool return; replaster; refill… ETA next week

I tried Inyo, no luck... I'm thinking there has to be a work-around for this... Just need to be able to install a Microbrite light where I have an 1.5" PVC flush with the edge of my plaster... I realize I can: 1. Lower the pool water below the lights 2. Get someone to carefully chisel out...

Here's a pic of the current installation situation...

Folks, since the pool is 95% complete [totally usable]; and much of my automation is on back-order; I'm trying to wrap up a few items: My 6x MicroBrites are mounted and working fine. However, the mounting is not ideal; as my PB was used to Hayward products and didn't plan properly to install...

Greetings TFP Community! We built a pool in 2021 and have all Pentair Equipment. Unfortunately, due to equipment shortages we have some "temp" hardware as we wait on our contracted versions... 1. EasyTouch 8 - - Waiting on Intellicenter Upgrade 2. IC-40 - - Waiting on IC-60 3. 2x Compool...

Here are some renderings with the openings

About 10x the amount needed… 2x 500 sq in openings. 1 low on right and 1 behind me in the picture. It’s also 500 sq inches…

Updated pic of the equipment area:

Thanks James…

So, an RS-485 utilizes a 3-strand data control wire (grn, yel, blk) that also carries 14vdc? But, this won’t work with my current EasyTouch Panel?? I have to wait until my IntelliCenter Panel arrives?

I gotcha. I sort of surmised that; but wasn’t 100%. If I upgrade to an IntelliCenter (whenever that arrives); I’m guessing that’s still a 2-wire…?? My Pool Builder is 100% Hayward. I convinced him that I only wanted Pentair. So I have to keep him honest With all the Pentair stuff.

Nice pic of the kitchen, too…