Search results

So, my dolphin died😢on season 3. I have been searching and searching and it seems like 3-5 years is max for these. I began searching for a new perhaps more affordable robot. There are many more options than when I first started shopping! My main complaint with my dolphin was that the cord is...

Top of the pattern should be good. Do you have an in wall skimmer? If so, I would fill to 1/2 inch from the top of the skimmer. Then watch your pump basket to make sure it stays full. My skimmer is a bit picky. Too full and it doesn’t skim well, too shallow and my pump sucks air to the basket...

Same single speed pump, psi was still 16ish. I have good flow

Ok, removed the flow switch. It looked clean, moved freely. I reinstalled it, viola flow light went off and it began generating! 6 hours later the no flow light is back on😩😡

It will be a few more weeks before I swim. I like a cool pool, but 66 makes my toes turn purple!

I bought two last time! I have had to replace them every single year!

I have not removed the flow switch yet. I have now replaced the pressure gauge, which is working 16psi, which is consistent with the last two summers.

I’m not real good at updating my log 🙃 There were lots of leaves this year at opening. I drained about 2/3 of the water. I scooped, brushed and ran my robot as I began to refill with city water. I dropped pH to 7.4 and added 2 gal of 10% liquid chlorine and started the filter. I added 4lbs of...

I have backwashed 4 times since opening about 10 days ago. The sand and filter are just under 2 years old. I haven’t done a deep cleaning to the sand, but did drain it for the winter and rinsed with water to open.

My no flow light is on. Does this piece pop off?

Never mind,.. figured it out. My pump and swg are finally working!!

Ok,.. I’ve replaced breakers to 20A GFCI, ran the wire in conduit, hooked everything up at the timer. When I switch one of the breakers immediately trips. I’m not sure I understand “ neutral load terminal” .

Do you want a pic of the GFCI CB installed, or the one that isn't installed yet?

Wait,.. do I just connect them to each other?? And am I supposed to have the neutral and the black line in under #1? The two white jumper wires are where they are when I bought the timer

I cannot believe you guys are still here for this. Thank you so very much. You are correct I do not speak the same language that you do. I’m trying to learn. So riddle me this, I still don’t understand how to connect the white wire from breaker2 and the white wire from the SWG to a neutral...

My pigtail from the breaker isn’t long enough to reach my neutral bar

Do I connect the white from the SWG to the white from the CB and not attach either to the A? Ok,.. so connecting the neutral swg to the CB just completes the circuit, without connecting it to the pump circuit??

?? I only have one screw for neutral??

@1poolman1 , thank you so much for taking the time to give me the detail I need. Does this plan look right?

Ok,.. I’m beyond confused now. My pump says 20 amp, SWG max of 8 amp. I have been running this all these years to a 120v, 20amp breaker switch. The timer that burned, I assumed burned because my pump was upgraded to 1.5hp and the timer could only handle 1hp. Do I have this all done incorrectly...

Uugghhh,… does my Intermatic T103r need to be connected to a GFCI breaker switch?

Thank you,.. exactly what I needed. It’s the terminology and abbreviations for the electrical instructions that throw me. I understand black, green and white🤪 I am using 12g solid wire from the breaker. I did notice this morning that the three wires from both the pump and the SWG are stranded...

I’ve spent several days doing just that. Perhaps I should be more specific. I have green, white, and black wires coming from my circuit breaker, my SWG and my pump ( 9 wires total). I need very specific instructions (pics are a bonus) as the exactly where each wire goes.

Update Power is ran from the breaker to the pool shed, 110V. The Intermatic T103r should be here in about an hour. Why can I not find a wiring diagram for this timer? I will wire my pump and SWG to one timer, but I’m finding no diagram to guide me. Any suggestions?

Can I run 110v to my Intermatic T104r? I’ve been reading and reading and I’m getting conflicting info😩