My flow is good and the water is 70 degrees. When I run the diagnostic test the cell light turns green and then goes off. Any ideas?
Intellichlor IC 40 Flow and Cell lights are off, Salt level lights flash red and green
- Thread starter twe
- Start date
- May 3, 2014
- 62,711
- Pool Size
- 6000
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
How old is the cell?
If the Flow light is not green, nothing will ever happen.
www.troublefreepool.com
If the Flow light is not green, nothing will ever happen.
Pentair Intellichlor ICXX SWG - Further Reading
www.troublefreepool.com
it has 4,000 hours on it. It was given to me my a contractor when my ichlor 30 was leaking.
- May 3, 2014
- 62,711
- Pool Size
- 6000
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
- Jun 24, 2021
- 16,165
- Pool Size
- 29000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-60 Plus
A blinking red "salt level" light on your Intellichlor IC40 indicates a low salt level.
How are you testing your water?
Do you have a salt test?
What is the salt level of your water from your salt test?
How are you testing your water?
Do you have a salt test?
What is the salt level of your water from your salt test?
- May 3, 2014
- 62,711
- Pool Size
- 6000
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
The FLOW light must be Green for the system to proceed past the boot up phase with is the red/green RR light sequence you are seeing.
Read the link I posted above. In the article is how to bypass the flow switch for a test.
Read the link I posted above. In the article is how to bypass the flow switch for a test.
You don't have a good flow light, so the salt test cannot work.
Check the flow switch.
Check the flow switch.
- Jun 24, 2021
- 16,165
- Pool Size
- 29000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-60 Plus
With No Flow the LED should be Red.
The lights look weak.
Maybe a burned out light.
Check the flow switch.
The cell electronics might be going bad.
The warranty is 2 years from date of purchase or installation.
The lights look weak.
Maybe a burned out light.
Check the flow switch.
The cell electronics might be going bad.
The warranty is 2 years from date of purchase or installation.
I tried the bypass - connected red and black and no change. I ran the diagnostic and now the cold water light is red.
- May 3, 2014
- 62,711
- Pool Size
- 6000
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
twe..
Kind of depends why the light is not working...
If it is simply a bad LED, then the cell should still work, as it would 'think' the green light is on with good flow..
If the circuit that detects 'good' flow is bad, then it might not be able to turn on the red or green flow LEDs and if it can't tell the flow switch is working it will not test the salt..
All that to say.. You have a bad cell!!! It does not matter how old it is, how many hours it has on it.. If the both red and green flow lights do not work, then it has to be the cell.
Thanks,
Jim R.
TFP is a registered 501(c)3 non-profit that is maintained by user donations.
The people who answer questions are volunteers.
If you find the site to be a good resource, please consider making a donation to help support the site.
Thanks.
www.troublefreepool.com
The people who answer questions are volunteers.
If you find the site to be a good resource, please consider making a donation to help support the site.
Thanks.
Become a TFP Supporter
Help Support TFP Trouble Free Pool is run by a dedicated group of volunteers that … Read more…
www.troublefreepool.com
Thanks for the replies. I went out and looked at it this morning and I do not have a flow light, but I do have a green cell light that I did not have before and I have a green salt level light which I also did not have before. I had to increase the chlorine output to keep the cell light on. I still have it wired to bypass the flow switch. Could this be working?
Similar threads
