Can anyone help with how to wire a Calimar pump interface board to a jandy aqualink? The instructions that come with the board aren't very clear. There are 4 wires. If someone can provide a pic of the jandy aqualink and circle exactly where the wiring should go, would help immensely.
Help wiring a Calimar vsp to jandy aqualink rs
- Thread starter _jackson
- Start date
Edited to add the pics if my panel
Attachments
Last edited:
- Jul 21, 2013
- 66,235
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
You need available relays which you do not have in your Aqualink.
You have open spots to add two relays if you have a RS8 board and not a RS6 board.
You have open spots to add two relays if you have a RS8 board and not a RS6 board.
Show a picture of your system and you will get a more informative answer. A random system won't necessarily apply to you.
- Jul 21, 2013
- 66,235
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
I don’t see available relays in your panel.
Take a better pic showing the relays.
You have a RS4, 6 , or 8 panel?
Take a better pic showing the relays.
You have a RS4, 6 , or 8 panel?
Here's how I set mine up. Works fine for my pool.
www.troublefreepool.com
You'll need one relay for each speed that you intend to use. Mine is set up for three speeds, but to be honest, two would be sufficient.
Any hacks for a remote controlled Black and Decker Pool yet?
Greetings; So, I'm in need of a second pool pump for my juacuzzi. I currently have a Pentair Intelliflo VSF, connected to their ScreenLogic or whatever it is called. It can control only one pump. Ran across this new Black and Decker 3HP pump, which is significantly cheaper that another VSF...
www.troublefreepool.com
You'll need one relay for each speed that you intend to use. Mine is set up for three speeds, but to be honest, two would be sufficient.
Thanks a lot for this. Here's more pics of my relays.Here's how I set mine up. Works fine for my pool.
Any hacks for a remote controlled Black and Decker Pool yet?
Greetings; So, I'm in need of a second pool pump for my juacuzzi. I currently have a Pentair Intelliflo VSF, connected to their ScreenLogic or whatever it is called. It can control only one pump. Ran across this new Black and Decker 3HP pump, which is significantly cheaper that another VSF...
You'll need one relay for each speed that you intend to use. Mine is set up for three speeds, but to be honest, two would be sufficient.
Attachments
- Jul 21, 2013
- 66,235
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Jul 21, 2013
- 66,235
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
That determines how many relays your Aqualink board can support.
Best way is to look at the labels on the back of the Aqualink PCB and look for a label that says RS4, RS6, or RS8.
Do you have IAqualink?
- Jul 21, 2013
- 66,235
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
It looks like four relays are being used and one relay is available.
You can add another OMRON G7L-2A-BUBJ-CB-DC24 if you can find it. Otherwise you can buy a relay from Hayward or Jandy for a higher price. Read Jandy Aqualink RS - Further Reading
Once you add the two relays you can wire up the pump for 2 speeds.
You can add another OMRON G7L-2A-BUBJ-CB-DC24 if you can find it. Otherwise you can buy a relay from Hayward or Jandy for a higher price. Read Jandy Aqualink RS - Further Reading
Once you add the two relays you can wire up the pump for 2 speeds.