Search results

Update for anyone it may help - the intellibrite LED engine (aftermarket) from sunseeker will fit the Jandy large Aquacolors housing based on diameter and thickness templates and measurement. They sell Jandy aftermarket gasket as well and it’s a perfect fit (added a thin layer of magic lube...

Sure wish there were aftermarket PCBs out there for Jandy like the Sunseekers for pentair intellibrite. Someone could be rich!

Another Handy (but Jandy) victim here. pulled fixture no water drops but condensation. Left in sun (upside down during rains and it dried out came back to life! in Green only (with dim blue red). Has anyone found a PCB 12v AC aftermarket option for these Light engine panels? Sun seeker has...

I have similar system. If your pump is not running then your intellichlor is not either (flow switch in the salt cell the intellichlor will drop to 0% output in the app when this happens). FWIW I find monkeying with the green on / off button for the pump is dangerous. If you set your pump...

Thanks again for info Allen and Dave, i will try spa 104 technique (wasn’t mentioned in procedure for two wire remote (see attached) for Raypak 8350, not sure if matters but there is a jumper wire on block from 21 to 23 that Intelliconnect manual said to remove & Raypak techical rep / prod mgr...

Actually I don’t use either of the two relays for the heater (one is for pump one for lights) there is a two wire heater control terminal on Intelliconnect. I can Set temp at 80 on my phone but if someone walks up and goes for 81+ the Intelliconnect can’t bring it back down. Very impressed...

HP is a two wire connection from Intelliconnect heater terminals to firemans at the HP block with external temp sensor Btwn pump and filter, was under impression rs485 is for Pentair hardware only (I have rs485 on a IntelliChlor but there are two more spots left open for another green and yellow)

Thanks and yes Intelliconnect controls HP but I’ve found if I set at 85 someone could simply walk up and change the heat to 90 via HP controls...if they do this it overrides the Intelliconnect and I can’t reduce remotely. Spoke to Raypak tech support and they say only option is a lockbox, seems...

Thank you Allen you are a scholar and a kind gentleman! this Intelliconnect is awesome just got the light to relay 2 and apparently is a Pentair LED so light show controls will entertain me for awhile! If anyone is thinking of this for your basic pool do it the Intelliconnect is awesome...

Thanks Allen what I meant to type was “yes I wish I had the benefit of a separate 120v“ for just the Intelliconnect but for now only have the 20A double breaker GFCI (240v) going in to L1, L2 then jumped to Line 1 and Line 2 on relay 1 This powers Intelliconnect, IntelliChlor and pump. however...

Great advice thanks Allen I am migrating from old Intermatic timer relay so I only had the 20A double breaker to power Intelliconnect Ichlor and pump. The Ichlor is now on all the time but the rs485 connection I believe will keep it generating only when flow and pump are there. I get the...

Thanks to some great tips from prior posters I was able to DIY Pentair Intelliconnect but can’t disable raypak 8350 digital control panel (those defiant teens and guests can set pool at 90+ when I’m not around). There are 3 pairs of wires from control panel board to main block labeled WS, DS...

Thanks AJW, makes sense I was wondering though if i could keep the timer wired as a doomsday control backup? When internet wifi is down for example? Guessing no I can’t because timer powers Ichlor power box which then powers Intelliconnect. Can’t imagine Intelliconnect saves all the network...

Moved from: Question connecting Intelliconnect to ichlor and the intelliph wall panel at the same time. So much good info here! Doing similar Intelliconnect install with IC40 no ph. Any opinions if I must take old intermatic timer out? My pump and IC40 power supply which will feed...

Any reason not to run 2 wires from heat pumps 10k temperature sensor to Intelliconnect? (would keep the existing wires from sensor to board not to disrupt manual mode if needed) Just thinking Intelliconnect would get same temp reading as heat pump thermostat was getting back in timer / manual...

Newb question for brain trust here. been diggin thru posts on Intelliconnect with heat pumps. After speaking with Raypak I learned my 8350 (digital) can be controlled by either 2/3 wire connection. Pentair install guide says Intelliconnect requires separate temp sensor with two wire plus two...