Search results

Thank you,

Thank you for the response, by the picture I included, is there an obvious relay to hook it to?

What’s the best way to wire a spa air blower motor in the easy touch 8 panel? The one I’m looking at is a Air Supply 2 hp 240v model Also, is it best to mount it on the air inlet, or put a T on the spa return and mount it there? Thanks!

I had a cover on the gfci outlet that had the foam weather seal between the body of the cover and the easy touch housing, however it had a clear lift able cover which allows for an extension cord to be plugged in. I believe that allowed too much atmosphere and dust debris to foul the outlet. I...

It was the GFCI. Lights work again. Thanks for walking me through some troubleshooting.

Thank you for the advice. I did use a screw driver to assist in resetting the gfci. I’ll check back after I replace the outlet.

This is how it seems. The breaker is standard 15a. The gfci will not reset, I disconnected the light wires from the black screw down sections in the panel. However each of the three that they are connected to have a jumper wire connecting them. Before I replace the gfci tomorrow, I’m going...

I also switched over to a vacant 15a breaker in the panel. No luck there. Still with the red light.

And it won’t reset. I disconnected each light wire at the relay / load center one at a time and tried to reset after each. Won’t reset. Hoping it’s just a bad gfci

I reset the breaker, the GFCI has a little red light on it now. The equipment is almost exactly one year old.

I realized what you meant after I posted. The GFI wasn’t tripped when I went out there. So I hit the test button and tripped it. Now it won’t reset. Maybe a bad GFI?

Is that the three little 3a breakers at the top right of the panel? If so, they haven’t tripped. All other breakers are good. Pumps and heater still turn on.

So just for fun tonight I fired up the screen logic to turn on the pool and spa light, and nothing. Screen logic says they are on, but nothing. Went out to the panel to manually turn them on, and i hear the circuit click, the panel light illuminates, but just darkness. I have a J&D LED spa and...

Thanks Jim,

That is what I’m talking about, it’s named “intelliflo spa light” I would like to just name it “intelliflo vs” if possible.

Last two questions: How do I rename the pump? How do i rename a circuit? I read your previous post, but cannot see how to do it in the config screens. thanks!!

yes, the Aux 4 is the Globrite lights.

Jim, you're the best! I renamed the Globrites "Pool Low" due to them being low voltage. I removed the first one in the special lights section and that did it. all lights come on at the same time, and no spa function. so what does this mean? sorry for the slow responses today, i'm putting...

the other pool light is what was the sam lights (globrite) there is no option for globrite in the menu, the closest is just pool light. there are two globrites. they should be wired together i would assume. i would have to look in the jbox. they are separate because they re low voltage.

Thanks Jim, i replied earlier but I don't see it here. I know what you meant in the other post, and i think my lightheartedness didn't come through in my reply. it's all good. The sam2 lights are Pentair globrites. there re two of them in my baja ledge. the pool light and spa lights are J and...

Here's the screenshot of the "all on" assignments, I don't see anything? - - - Updated - - - Doesn't look like there is anything there. There's no problem just turning them on one at a time, but that's not the point. It's doing something that it shouldn't, and I would like to resolve it. i...

I’ll look into that as soon as I get back home. I’ll update as soon as I do. Thanks!

No I don’t, and the other thing I figured out this morning is that if I turn the lights on individually, it doesn’t happen. However, if I hit “all on” in screen logic on my phone, that’s when it occurres. Baffled.

Jim, here are some screen shots of my configuration. when i turn the light on, not only does the spa turn on, the valves turn as well....