Search results

Oh hmm! I guess I've never paid attention to the light before :unsure:. The only reason I thought it was because it's not working and I'm used to green = good, red = bad in most cases. I will try resetting the breaker tomorrow on the pool equipment tomorrow, thanks Jim.

Hi all, We had a bit of storms recently and my protocol adapter has a solid red light now. Tried power cycling, holding reset button in, etc. Anything else to try before I call it fried?

Disregard, got it with Pentairs help. Didn't know about the 3-push trick on the reset button.

Anyone? I am still struggling. Still stuck at "Connecting to Relay Server at 69:94:nn:nn:7576" I'm guessing some filtering on my AT&T router but still not finding anything else to turn off on it.

Just from internet searches, might've even been an old post from this site's forums, i'd have to search again, but it's good to know it's not required at least! So it just sits at "Connecting to Relay Server at 69.94.xx.xx:7576 (it actually shows a valid IP, I just didn't know if it was mine so...

Hi all, I'm having a problem connecting from remote to my Screenlogic. I can connect on wifi with no issues. When I try to connect remotely it says "ERROR: Cannot connect. Error #60 in connect(): A transmission timeout occurs during a read attempt" For what it's worth, I can't connect to...

Hi all, I'm a 16x32 rectangle pool owner in Texas. I'm using liquid chlorine from a local chlorine bulk seller for $2.75/gallon (10% strength). I was born with a bit of a quirk - I prefer to swim fully clothed vs wearing a typical swimsuit. A typical "swimsuit" for me consists of a long...

First - I clean my filters every 3-4 months. Every time I have this big pile of lint. We do tend to wear a beyond abnormally excessive amount of clothes in the pool. Any harm? Second - what’s the easiest way to prime my pentair intelliflo after cleaning - I’ve battled this challenge for...

I’m using a keto-ai smart skimmer but my Taylor and Leslies read the same. To clarify, I didn’t get to test the alkalinity while the pH was >8. But my pH climbs daily and I add acid every other day roughly to keep my under 8. I probably need to test TA more often but I tend to test it when the...

I used my Taylor kit and then had Leslies check it too.

Hi all, 15k gallon non-salt water pool. My TA was low 4 weeks ago (30) so I added 16lbs of baking soda. The pH kept rising to 8+ super fast after that so I kept adding muriatic acid to bring it back down. Today I tested my TA again and it's only 47, so I added 4lbs baking soda. My pH is rising...

This is the ones we always use, always seems like a fair price and lots of colors. https://amzn.to/3wgrQeo

$800 seems high, I think I typically spend $500-$600 tops for the larger pool sized and a couple hundred less or so for the spa sized ones, unless they've hit a supply problem like everything else is lately...

Hi all, Before I went on vacation, my pentair easytouch wireless remote transceiver went out so I changed it out and it resolved the issue. While on vacation, we had some power outages. Now that I'm back, my clock is permanently set to 12:00 in the year 2000. When I try to set the clock via...

Hmm, maybe that's what's inside the box that's inside the box. I'll have to go thru the steps and see what I end up with. So now that I have this, is it silly to also still continue using the wireless remote as well? If so, maybe I didn't need to replace my wireless remote PCB after all.

Hi all, I'm a little confused by the EC-522104 that I just bought and received. It shows on the diagram that it needs a CAT 5 running from it to my wireless router. If so, that means I need to run a CAT5 from my easytouch panel to a network jack which isn't going to be fun. When I ordered it...

Very interesting - when only the pump is connected, it works! What does that mean? I ordered a new pcb for my wireless remote and a wireless kit to add. Is the likely bad wireless pcb likely causing other issues?

I’m confused now because where it says Filter Pump under the filter pump and auxiliary relays (J8) there’s nothing plugged in. And it was working fine a week or two ago. I’m trying to figure out which of the three going to J20 is the pump, tracing them is hard with conduit :(.

Boo It just went back to NO COMM on the pump status after the reset seemed to briefly fix it.

I just did a reset and it says status normal now and the pump just kicked on.

Sorry i’m confusing things. At the easy touch it says Status: NO COMM! The pump says running schedule 0 rpm and if I hit speed 2 or 3 it speeds up. So not only does my remote not work, the pump status is also saying No Comm on the easy touch.

Merged threads. TFP Mod Hi all, I'm going out of the country for a couple weeks in a few days and freaking out a bit because my Easy Touch programming is wonky. I ordered the wireless kit but it won't be installed in time, and my remote quit working the other day, so I'm going to have to...

Merged threads - TFP Mod Hi all, I've somehow managed to get my EasyTouch programming all messed up while troubleshooting my wireless transceiver board (which I have on order as there's no LED lights on it even though it's getting 15V). First question: I dont have the ScreenLogic2 so I can't...

Thanks @mknauss much appreciated. Hopefully @ogdento will be able to help! Interestingly, my spa side remote no longer has power either, but that stopped working a couple months ago. I finally found my multimeter, so I'm going to see if I can test some voltages but not totally sure what I'm...

Hi all, My easytouch remote is suddenly not talking. I already tried re-pairing it but it's not. I took off the cover and NONE of the led's are lit or flashing (not even power). What next?

Keto-AI. It’s been very accurate so far.

I’ve been paying $1.99/gal at Napco in Spring for 12.5%.

Hi all. My pH seems to be climbing pretty aggressively lately. Is it most likely due to the fountains running more due to the freezing temps going here in Houston?