Search results

I just found where to adjust it in iaqua link - its under System Setup --> VSP Setup --> Speed Setup --> ePump Filtration 1 --> Freeze Protect Speed

Ditto! Same pump and setup as you (presumably iaqualink) - I can't find how to adjust my freeze protection speed.. I normally run at 1700 but my freeze protect is coming on at 2500...

Similar situation here in Raleigh NC - it is our first winter with the pool and I am keeping it open (because it's a very expensive water feature and I'd like to enjoy it year round!) The chlorine generator stops itself from generating in cold temps so I don't know if I need to code it off or...

Well folks.... seems Jandy tech support and a few of you called it out. It was the temperature sensor!! How I got there.. I completely checked every copper wire connection and learned how modular everything is for easy access. All copper wires good. After rebooting - no joy. I then...

Mine isn't physically present because my PB is similar to yours.

Wow - thanks! Called Jandy and within 60 seconds he recognized I have no water temp sensor on the aqualink (my builder forgot to install one). He said this is required for the aquapure to turn on. I let him know that I can press the TEMPerature button on the panel and get a reading from the...

Hello - that i am setting it from iaqualink (the screen shots are iaqualink, no? It's entirely possible I'm calling these things out incorrectly). Yes, I hit the "ENTER" button in the lower right corner each time. Iaqualink retains any number I type, confirmed by coming back to the screen...

Thank you Dodger and I fully appreciate everyone’s time and help. Perhaps it’s not been conveyed clearly across the multiple replies, but I felt I had provided all of the information James was inquiring about across my posts but here is again. I’ve jus run through everything again with time...

That’s the point of this whole thread.

Not in spa mode. Yes it takes it in iAquaLink but has no effect on the panel.

James that’s what we’re troubleshooting. I perform those steps but it doesn’t actually take at the aqua pure.

Yes. It only shows in iAquaLink. Never reflected on the physical panel in normal mode. If I go to service mode it will flash the number initially but not during operation.

Just tried this. The aqua pure does shut off when the pump is off. Flow shows on. It retains 40 in iAquaLink on the Pool button but it remains as 00 on the panel and cell does not show on. Pressing status also shows 0%. If I enable boost from iAquaLink it does show cell on but 00 on the panel.

Pics of the equipment wiring. Let me know if I need to take a picture of anything else.

When I do a boost The aqualink panel shows JB and 00%. The iAquaLink app shows boost and the time left. If I press the up down arrows on the panel it beeps and says ja and goes back to 00%

Ok thanks. Yes that’s how I’m accessing it and it shows salinity and boost but never shows the percent production. The builder is not responsive and every time they step foot on my property they break something and have every creative excuse in the world. I’m sure it sounds like I’m just...

Interesting. Ok mine is set up for epump but I do have a Jandy variable speed so presumably that part is correct.

Thanks - I did just that. It is a new system, for what it’s worth.

Similar issue here.

Where do you look and change this setting? I have the same issue and want to see if this may be a cause.

I have Similar issues I’ve seen here where I can set a number in aqualink but the control panel of the aqua pure always shows 0%. This is a brand new setup part of my recently completed pool. My pool builder is useless so there’s no recourse going back to him. I can enable boost from the...

I have the same issue. How can I even check if a temp sensor has been installed?

I tried a Doheny Saturn but returned it because the cord would tangle every day and create so much tension where the robot was unable to move forward. Anyone know if the Doheny Discovery comes with a Swivel and avoids that issue?

Eye candy

Some pics

The pool was filled today! And I am hopeful I can get some advice from the forum!! Would you believe the new supervisor (who was great!) called me this morning to let me know he quit last night! This is a guy with 30 years experience who pushed all of the crews to finish my pool, and he's been...

What a nightmare. After fixing the steps almost 2 months ago there’s been very little progress. It doesn’t appear the builder was ever going to consider offering money off. Instead he made my contracted “oversized” steps into standard 12” steps. They added some rebar and measured so hey could...

Problem!! Our pool builder screwed up the steps and tanning ledge. It looks like the crew who did the rebar made the first step where a measurement line was vs the actual first step line. This has created a much smaller tanning ledge and the left area of the steps unusable as steps (because...

Thanks!!!!!

All done! My PB said not to hose the pool at all - any ideas why that might be?