Search results

Have replaced my trusty Jandy pool lights 2.5 times in 10-years and I now have to replace half of them (four lights). Right now, every light is a JLU4C6W100 (6 watt). The pool looks great but I definitely have some dark spots. Since I have to replace some of the lights I want to consider 12W...

Have a Jandy JX pool/spa heater that does not get to temperature. If I set the spa to 104 the water gets to low 90s. Water flow seems good, the heater fires without a problem and I replaced the temperature sensor. It seems like a calibration issue, however, when I go into the calibration...

I have a four year old Jandy JXi Spa heater (2nd one). It gets the spa to about the low 90s but will not heat up all the way. Everything else works fine. I have heard that waterflow issues can cause this. Seems like waterflow is strong at the main outlet in the spa, if that's an accurate way...

I have a Jandy SHPF 2.5 pump running between my vanishing edge tank and waterfall. It started to may a whining noise last week. Took it apart and saw that the impeller was worn. Ran the motor and it sounded fine, so I replaced the impeller and diffuser. Just put it back together and it’s still...

In 2019 I replaced eight Jandy JLUC10-100 lights that failed after only four years of service (actually, half of them failed but they were discontinued so I replaced all eight). The new lights, Jandy JLU4C12W-150s, were much brighter and appeared to be of better quality, so I was ok with...

I have a two-year-old Jandy JX I 400 spa and pool heater. My son went to fire up the spa a couple nights ago and got an ignition step error. The last time we used the spa was probably two weeks prior. Called my maintenance guy to take a look and the first thing he noticed is that the tank is...

Hello TFP Community! I desperately need some advice and I apologize in advance for the long post. I have a seven year old in-ground salt water pool with above ground spa w/spillover, 3 separate waterfalls, and a vanishing edge. I estimate the pool to be approximately 40K gallons, so its...

I know there are lots of posts about robotic pool cleaner recommendations, but I wanted to list my specific needs to get the best recommendation. My Polaris 9450 finally failed. I think water got into the cable connection on the robot. Besides this, its pretty beat up. It has served us very...

As of this morning, my iAqualink RS Wireless OneTouch is down. While in Auto mode the display for the chlorine generator and lights for the control panel buttons are all off. If I power cycle the system by turning off the iAquaLink breaker and turning it back on, it attempts to start in Auto...

I recently replaced my SWG - Jandy Aquapure 1400. I had some issues at first but everything has been running nicely for a week or so. I set the salt level to 50% per the instructions. Chlorine has been in the 1 -2 range per my Taylor test kit. I added some shock yesterday and boosted the SWG...

Disclaimer: I'm pretty new to taking care of my own pool. After running some tests behind the pool co. I quickly learned that my chemical levels were not Ideal so I decided it was time to take things over. My first order was to replace my Jandy Aquapure 1400 Salt Cell. I was getting a service...

Hello and thank you for such a great forum! I have a five year old pool in the Atlanta area. It’s large - estimated 40K gallons. My Jandy Aquapure 1400 has started throwing 120/121 codes intermittently. About three weeks ago I had a 120 code. After removing and inspecting the device (it was...

Hello! Great forum! This is my 1st post. Jandy just replaced several of my nicheless pool lights under warranty as a few of the original lights failed. Great customer support by Jandy! They seem pretty straight forward to install. Just wondering if I need to lower the water. Guessing not but I...