Unplugged the Antenna and the pump displays “display not active”. I will leave like this for few days.
Also, what is the life on these receivers?
Also, what is the life on these receivers?
Pump 1: Communication Lost / Pump Status: No Comm!
- Thread starter Pieroz
- Start date
- Jul 21, 2013
- 52,854
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Ok thank you Allen! I noticed there are two lights on these receivers, TX and RX. The Tx was working but not the RX. .
Do these receivers come together or I can buy one of them only ?
Do these receivers come together or I can buy one of them only ?
- Jul 21, 2013
- 52,854
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
They are a matched pair with an encryption key. The numbers of both devices must match for them to talk to each other.
@ogdento has hacked them and figured out to change the key to create a new pair.
P,
The antenna on the EasyTouch is often taken out by nearby lightning strikes..
As Allen point out, you need both sides. The link in his post #13 includes both units.
Thanks,
Jim R.
The antenna on the EasyTouch is often taken out by nearby lightning strikes..
As Allen point out, you need both sides. The link in his post #13 includes both units.
Thanks,
Jim R.
@Pieroz as Allen said they are only sold as a matched pair with that key.
I wrote a post about how to reset the code on the "Quest" version of this link, but you've got the earlier "Viper" version that has a Microchip brand radio module... I haven't figured out how to reset those codes yet. I think I have half of one of these Microchip sets, so if you'd like to send me your dead unit I can investigate...
I wrote a post about how to reset the code on the "Quest" version of this link, but you've got the earlier "Viper" version that has a Microchip brand radio module... I haven't figured out how to reset those codes yet. I think I have half of one of these Microchip sets, so if you'd like to send me your dead unit I can investigate...
just replaced my Polaris 380 wall connector with see photo attached. The water is coming out where the black area is ( pressure relief valve), any idea why ?
- Jul 21, 2013
- 52,854
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Unscrew the PRV and examine it.
Replace the PRV. They wear out and break.
If water still blows out the PRV it means there is a clog in the feed hose or cleaner.
Replace the PRV. They wear out and break.
If water still blows out the PRV it means there is a clog in the feed hose or cleaner.
The pressure is still blowing out of the PRV.
The pressure from the wall is good. From testing the feed hose, they look that the water is going through. How will I check the cleaner ? I did what I can looking and seems the water goes through. Could the booster pressure be too high? My pool pump is at 1800 (set by the pool company that opens it) and my cleaner is at 1850.
The pressure from the wall is good. From testing the feed hose, they look that the water is going through. How will I check the cleaner ? I did what I can looking and seems the water goes through. Could the booster pressure be too high? My pool pump is at 1800 (set by the pool company that opens it) and my cleaner is at 1850.
- Jul 21, 2013
- 52,854
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Post pics of your equipment pad and create your signature with details of your pool and equipment with model numbers please.
You adjust the pressure by using the red or blue discs that can with the Polaris. Do you know which one is installed in your UWF?
You adjust the pressure by using the red or blue discs that can with the Polaris. Do you know which one is installed in your UWF?