MITBeta
Gold Supporter
- May 28, 2020
- 1,222
- Pool Size
- 13000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
New to Saltwater
- Thread starter careingemt
- Start date
Thanks to everyone for helping me through this process... Appreciate it alot
No problem - we've got you. As stated above, you let your chlorine drift too low for your CYA level, and more than likely have algae brewing. Read through the guide on the SLAM process, really you're just keeping CL and at an elevated level until you eradicate the algae. The closer you can monitor it, the better it'll go. Keep your pump running, and brush frequently.
think I'm gonna drain my pool to lower the cya after I get the slam done
what's the best way to add in stabilizer if need be... can I add it into the skimmer?
what's the best way to add in stabilizer if need be... can I add it into the skimmer?
- Jun 22, 2014
- 47,861
- Pool Size
- 17888
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
Adding CYA:
To increase CYA via granular stabilizer, place the required amount as calculated by the Poolmath calculator into a white sock and place in the poolside skimmer basket. For those concerned about suction flow to the pump, suspending the sock near a return jet or from a floating device will also suffice. Best never to allow undissolved granules to rest directly against the pool surface. After soaking for about 20-30 minutes, squeeze the sock often to help it dissipate. Once dissolved, consider your CYA adjusted to that programmed (target) level. CYA test readings should show a rise in 24-48 hours, however some pools may experience a longer delay to fully register. Best to confirm final CYA in about 5-7 days before adding any more stabilizer/conditioner.
- Feb 6, 2015
- 6,166
- Pool Size
- 12300
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
Exactly!
And use the FC/CYA Levels for dosing FC based on your CYA level. Never let the FC fall below the minimum. Shoot for the high end of the target range (or a few higher if your FC loss puts you below minimum at the end of the day).
You'd be much better off doing this BEFORE you do a SLAM. You'll get rid of half the algae, and be able to use less chlorine to kill the other half.
so ive figured out how much salt is recommended which is 175# for the swg is there a way to decipher how many ppm this is? (like 2600 or 3200 or 3600) like what reading should i get when i test for salt
Not sure I understand - how did you get to the recommended 175#? That is going to give an entirely different PPM based on what pool size you have. The SWCG will need a certain PPM salt to work properly, normally you would then test your pool for salt (most pools already have salt in them from other chemicals), and then use PoolMath to figure out how much salt you need to add by using the "effect of adding chemicals" functionality. Do you have a way to test for salt level?
In your 7000 galloon pool, every 100# of salt you add will raise the salt level by 1700 PPM
i called swim waves customer support and they recomended that for my pool size
yes i have a way to measure salt amount
here is a picture of my swg which says 18' 52" my pool is 42" deep
OK - that's find and dandy, but that likely assumes you start with 0 salt in the pool. I find it really odd they don't give a PPM that you should be aiming for... that said, the SWCG is either happy or it's not, and should give you a warning if its too high/low on salt.
Basically they're telling you you need 3000 PPM of salt - that sounds reasonable (175 lbs in a 7000 gal pool = 3000 PPM). So test your current salt level, and then add what's needed to get you to 3000 PPM.
It's easy to add, but not easy to take salt back out, so add slowly or under-estimate how much you think you'll need, test, and add more as needed.
MITBeta
Gold Supporter
- May 28, 2020
- 1,222
- Pool Size
- 13000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
My manual says on top P5E0004000.... it does state that the optimum salt levels in the pool water is between 2500-3500 optimal is 3000ppm
so yes id say thats my swg my apologies
according to TFP are we at all concerned with metals like copper ?
MITBeta
Gold Supporter
- May 28, 2020
- 1,222
- Pool Size
- 13000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-45 Plus
Yes, we are concerned, and avoid products containing metals.
Metals - Further Reading
www.troublefreepool.com
the other week when i had my water tested at the pool store it stated a 2.8 level for copper ... how can i get this to 0Yes, we are concerned, and avoid products containing metals.
Metals - Further Reading
Similar threads
