Recent content by guinness

  1. G

    Pentair IntelliCenter Installation Questions/Issues

    When I had that message I was able to get the wireless working by pressing the reset button on panel for 10 seconds and afterwards it worked.
  2. G

    Easytouch vs intelliconnect

    The new IntelliCenter is another option that already has ScreenLogic functionality builtin (like the IntelliConnect). The IntelliConnect Review gives you an idea of it's features, but it's a basic system w/ 2 relays. But since you've already purchased EasyTouch you'll need ScreenLogic to get...
  3. G

    Can you identify this pool light?

    Also ensure that you have the pool light wired to a RCD (residual current device).
  4. G

    Safety Bracelets for Kids. Do They Work?

    Good Housekeeping reviewed some of the pool alarms https://www.goodhousekeeping.com/home-products/pool-alarm-gate-reviews/a12136/best-pool-alarm-gate/
  5. G

    Omnilogic relays failing after update of firmware

    @Hayward Pool have helped with issues in the past, but they don't appear active anymore. Maybe ask if sending the board in for repair is an option. New boards are north of $600 so worth asking. Hayward OmniLogic Main Control Board Replacement HLX-PCB-MAIN
  6. G

    IntelliCenter Home Automation Integration and Control

    I had discovered two open TCP ports 6680 & 6681 last month in this post and the website dumps a lot of these messages to the console. You can just telnet the latter port and send/receive messages.
  7. G

    Adding Automation, Actuators, EasyTouch, SWG at same time? Doable as DIY?

    What are your expectations for automation? Since you have a pool/spa combo is automating valves (with actuators) and heater (via the firemans switch) desired? If you have a limited budget then the Intermatic MultiWave might be an option. The PE25065RC at $650 would allow you to do this and...
  8. G

    Hayward OmniLogic system loses Wi-Fi configuration

    The Omnilogic HLWLAN antenna is actually a rebranded EnGenius ENS202EXT acting in bridge mode. It's worth noting that Pentair is also using that same device as a WiFi bridge for their new IntelliCenter. I suspect that all the WiFi settings are actually stored on the ENS202EXT and the...
  9. G

    Change Router and Lost Screenlogic Connection

    Also see following thread. https://www.troublefreepool.com/threads/screenlogic-issues.182107/
  10. G

    Help Fixing Pool Light: Cord or Light?

    The panel in the photo is for a low voltage lighting system, but the pool light appears to be 120V. You definitely need to ensure that you have working GFCI protection that will trip or shut off the circuit immediately. Below is some useful information regarding pool lights and the need for a...
  11. G

    Omni Pool Control Firmware Update

    I would take a pause and follow Omnilogic relays failing after update of firmware post. It might be an isolated incident, but I'd give it a few weeks in case any kinks need to be worked out.
  12. G

    Omnilogic relays failing after update of firmware

    I'm not familiar with the OmniLogic is the update done via a USB? The firmware image might've been corrupted. Can you remember what the error message was when the MPP update failed? Are you able to reapply the firmware update again or is it not letting you? If you can, you might try to drop...
  13. G

    Pentair Sun Touch solar programming

    In system control can you take SunTouch out of auto mode and manually switch solar on and off? If that doesn't work inspect the wire from the actuator for any damage.
  14. G

    Pentair IntelliCenter Installation Questions/Issues

    Also make sure that you have the ethernet cable plugged into the correct port (marked POE) on the wireless client bridge antenna.
  15. G

    Light Niche missing screw hole

    Get two light wedges and put one at the top and another at the bottom.