I installed a Hayward OmniHub for my inground pool. Everything except comunications to the pump seems to be working well. I have the HLPMPCONV installed and the controller sees it, but it doesn't seem to generate a HUA for the pump. I have done everything that I've seen on here (Hayward technical document). Still no luck. Tried a different HLPMPCONV board and new control cable to the pump. Any suggestions would be a big help. Thanks,
Hayward OmniHub and Pentair SuperFLO VST
- Thread starter attessa
- Start date
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Welcome to TFP.
Latest Omni firmware is 5.0.4. 3.2 is over 5 years old. Upgrade your firmware and see if things work properly.
www.troublefreepool.com
@ChrisLPC may have other ideas.
Latest Omni firmware is 5.0.4. 3.2 is over 5 years old. Upgrade your firmware and see if things work properly.
Hayward OmniLogic - Further Reading
www.troublefreepool.com
@ChrisLPC may have other ideas.
Yeahp. Firmware update everything. Make sure the dip switches on the pump are set correctly. Make sure the breaker to the pump is off for 10 minutes before changing dip switch settings.
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Hayward says it supports IntelliFlo pumps.
Chris, do you know if it works with a Pentair Superflo VST pump?
Chris, do you know if it works with a Pentair Superflo VST pump?
Can you show us some pictures of the wiring at the pump and OmniHub? Specifically the com wire.
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
I think you have the yellow and green wires reversed from the pump connection on the converter board. Try changing them.
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Different Pentair pumps have slightly different RS-485 command sets. It is not clear the Hayward board works with pumps other than the IntelliFlo.
I did finally hear back from from Hayward. The system is supposed to talk to the SuperFLO VST. Here are all the pumps it is supposed to communicate with;
Intelliflo VSF 011056
Intelliflo i1 011059
Intelliflo i2 011060
Intelliflo VSF 022056
Intellipro VSF 013004
Whisperflo VST 011533
Superflo VST 342002
SuperMax VS 343001
Intelliflo 3
Sta-Rite
Intelliflo VSF 011056
Intelliflo i1 011059
Intelliflo i2 011060
Intelliflo VSF 022056
Intellipro VSF 013004
Whisperflo VST 011533
Superflo VST 342002
SuperMax VS 343001
Intelliflo 3
Sta-Rite
- Jul 21, 2013
- 65,473
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Thanks for getting this list.
Did something get cutoff in your paste after Sta-Rite?
Do they have any advice on how to get your pump working?
That is the list exactly as sent to me. 2017 and newer it said. I was told my setup is good and I should have no hiccups. They have been less than helpful.