I have an IntelliCenter that won’t connect to WiFi . When trying to connect it just discovering for networks but never shows any. Then when I try to put info for app it just times out. Any ideas?
IntelliCenter WiFi issue
- Thread starter Landrade2016
- Start date
Did your Intellicenter come with a WiFi antenna or the wireless kit? Older Intellicenter kits were shipped with the wireless kit. The wireless kit won’t show up as a wifi network. It has to be plugged into a router. I ran into that problem with mine.
Mine came with everything panel and both wireless antennas. The outdoor one and the indoor one too
If you have an indoor and outdoor antenna, that sounds like the wireless kit. The WiFI antenna is only one antenna connected to the Intellicenter. Do you have the indoor antenna plugged into a router with a Cat 5 cable?
Which app are you using? There’s an Intellicenter2 app and a Pentair Home app. The Intellicenter2 app should show your system as a “local” system. The Home app probably won’t work. Pentair has to “migrate” your Intellicenter over to the Home app.
So the thing is that apart from the WiFi . I tried creating new account on the panel and it just times out.
It is apart from the WiFi. The wireless kit interfaces with your router. Then you can access your system via WiFi through your router connection. The Intellicenter panel itself is not connected via WiFi and the panel will not recognize a WiFi network. Are you using the Intellicenter2 app? If you are, is your device (phone, IPad, etc) connected to the same WiFi network as your router?
Yes but when I try to connect on panel it just loads until it times out . I’m using an iPhone and IntelliCenter 2
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Do the Internet Connection Test on the outdoor panel.
See page 85 in https://www.pentair.com/content/dam...als---user-docs/intellicenter-users-guide.pdf
Do not do "Connect to Wireless Network"
If using the Pentair High Power Wireless Link kit skip to the Internet Connection Test. It should show you are connected. Then register the user using the OCP.
See page 85 in https://www.pentair.com/content/dam...als---user-docs/intellicenter-users-guide.pdf
Do not do "Connect to Wireless Network"
If using the Pentair High Power Wireless Link kit skip to the Internet Connection Test. It should show you are connected. Then register the user using the OCP.
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Once you pass the Internet Connection Test then On Add New Account - remove your address. They don't need to know it. Put in your email, name, and password and press the check on the upper right. See if it asks for anything else. Give it the minimum they require.
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Review this thread where I walked someone through the Wirelrss Link setup…
www.troublefreepool.com
IntelliCenter2 new panel not working
Hi experts, I posted about a month ago about my intellitouch not working, had someone come out and said the board was bad, so upgraded to a IntelliCenter2 panel and it has been 4 weeks of troubleshooting and calls and still not working. Hoping for some help before pool person comes again for the...
www.troublefreepool.com
So I did this and it says it’s connected but yet I can’t make a login . Do you know why it times outDo the Internet Connection Test on the outdoor panel.
See page 85 in https://www.pentair.com/content/dam...als---user-docs/intellicenter-users-guide.pdf
Do not do "Connect to Wireless Network"
If using the Pentair High Power Wireless Link kit skip to the Internet Connection Test. It should show you are connected. Then register the user using the OCP.
Is there any way I can message you tomorrow around 10 am im central time zone btw. I’m at work but would love help on thisReview this thread where I walked someone through the Wirelrss Link setup…
IntelliCenter2 new panel not working
Hi experts, I posted about a month ago about my intellitouch not working, had someone come out and said the board was bad, so upgraded to a IntelliCenter2 panel and it has been 4 weeks of troubleshooting and calls and still not working. Hoping for some help before pool person comes again for the...
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Good. Your panel is online then.
We need to get you connected locally using the local systems IP address and logged into the Pentair cloud for remote control.
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
I am busy tomorrow until mid-afternoon. I will post here when I am back online.
Ok perfect I will let you know if I can get it going . Thank you so much
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
I prefer to conduct business in public where others can learn from it.
- Jul 21, 2013
- 65,118
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Similar threads
