Search results

Search the forum Search WordPress Search MediaWiki
  1. C

    Broken water temp sensor disables aquapure?

    I you have a JXI heater a bad water temp sensor will also stop it from working.
  2. C

    Aquapure 1400 121 Error

    Replace cell
  3. C

    Jandy aqua pure 1400, getting general fault error

    You have to watch the display for a few minutes. Code comes and goes.
  4. C

    Jandy iAqualink RS8 Auto Mode not working

    If the jumpers are in the wrong position it will cause problems.
  5. C

    What's that hole for?

    Stick a hose in it and see where the water goes. A lot of these go in to underground drainage and you may never se it exit. I" not crazy about drains because they take away your chems. Having a pool to full does not hurt anything.
  6. C

    Pump is not priming and water is coming back from the filter when strain lid is open.

    impeller is probably clogged. Open up pump and clear
  7. C

    More on Jandy 1400

    If you got 5-6 years out of it that was very good. Most cells don't last that long. Don't worry about what caused it just get a new one. You got your moneys worth. You would have spent twice that in chlorine.
  8. C

    Weir stays open

    Cheap enough. Buy a new one.
  9. C

    Pump Connections

    Jandy changed the connections about 8 years ago. You probably have the old ones. The ones in the link will not work if this is the case. Send a picture and I can tell you. I might can find a part number if I can see them
  10. C

    Pool Filter/Pump don't turn on

    You could have a bad breaker that gives power to pump. New code is to use ground fault breaker on pumps. These look like they are not tripped but can be. flip it back an forth hard.
  11. C

    "no flow"

    Sensor probably needs replacing but try turning power of to whole system and back on. Reboot, Sometimes this works.
  12. C

    Can't detect air leak

    Check valves in front of the pump. They have o-rings that can go bad Check o-ring on pump lid. Make sure skimmers a full and doors are not stuck up. Your priming problem is air getting in from somewhere in front of pump.
  13. C

    Winter Time aquapure plc1400

    Add a few bags of salt. Turn the AP down to about 20%. Run the pump less to save electric. Check the chlorine levels in a week or two. The apure will stop making chlorine at 52 water temp because you hardly need any chlorine with cold water.
  14. C

    Jandy salt system

    Apurem will connect with the red 4 pin connecter. If you get the FSOFT1400. The cell is easy to clean and cheaper to replace than the PLC1400.
  15. C

    NO FLOW always on

    Stop wasting time and get a new sensor. Make sure you get the latest one or you will have the same problem again.
  16. C

    Main pump stopped working today

    Just save the headache and get a new Pump. If there is any way you can get a VS it dropped my electric bill by $80 a month. Pays for it self in about a year. And in some areas the power company will give you a rebate for going VS. In my area it is $250
  17. C

    Pump won't turn on - Jandy Stealth

    Is the waterfall pump on the same breaker. Usually not.
  18. C

    Filter pressure on Jandy 340CV

    Don't think you really have anything to worry about.
  19. C

    Pump and SWG issues

    A single speed pump has 3 wires. A 2 speed pump has 4 wires. A VS has same wires as single speed pump. The 170 is usually the sensor. If you have a Jandy Controller it probable best the stick with all Jandy. Plumbing can be a pain if you go to a different brand pump.If you don't have a Jandy...
  20. C

    NO FLOW always on

    Replace with a new style sensor
  21. C

    Am I expecting too much from my pool cleaner?

    If it is getting too much pressure it will tangle in back up mode. go look at the books and it will show you ways to adjust the pressure.
  22. C

    Polaris Feed Hose Too Stiff???

    They get stiff when they get old and worst if old and cold.
  23. C

    Spa mode back draining during operation

    The return line valve is in the wrong position. What kind of system do you have. There is a toggle switch on the valve to change it.
  24. C

    Waterfall mode vs Spa Fill mode

    spa fill moves auto valve so all the water goes to the spa and not the pool. The waterfall button probable turns on a booster pump. do you have a remote or controlling from the panel?
  25. C

    Pump won't turn on - Jandy Stealth

    This is usually an indication the the breaker in the panel is tripped. Even though it doesn't look tripped go back and forth a few times. The jandy system will show it on but that doesn't mean power is getting to pump.
  26. C

    4 week old polaris 280 going in circles

    There is a little nipple and the back bottom that can be adjusted. It may have got knocked to the side which would make it do that.
  27. C

    polaris

    Just run it again. You may have messed up the seal and it will leak.. If it doesn't leak you are all good
  28. C

    Water level raised by rain.

    The only problem with water too high in pool is the skimmers can't work as well. If you drain every time you are draining the chems you just paid to put in. Just give it a chance to evaporate. Chems stay behind with evaporation. So what if it overflows.. it is the same amount of water that is...
  29. C

    Salt day has arrived, finally so a couple questions

    The system will work from 2500-4000. Sweet spot is around 3400. In most average size pools one 40lb bag will bring it up 300ppm. The way I do it is when it gets in the 3000 range I add one whole bag. I never do half bags and I don't keep extras. Just buy one when you need it
  30. C

    Jandy Aquapure 1400 Salt Chlorinator

    There is a way to install 2 cells. Call Jandy tec support. Also I take care of a big pool and what we do during the hottest part of summer id add additional chlorine because the cell just barely keeps up.
Top Bottom
Back