Salt

Salt for a SaltWater Chlorine Generator (SWG)

Salt is required with a saltwater chlorine generator (SWG). Salt can also be added to the water to enhance the subjective feel of the water. For an SWG, check the manual for the correct salt level for your unit. This level will typically be around 3,500ppm, but varies with manufacturer.

Salt for Improved Water Feel

For improved water feel without a SWG, try levels around 2,000ppm.

Salt Levels

These levels are less then one tenth of the salt level in ocean water, which has around 35,000 ppm of salt. People vary in their ability to taste low levels of salt. A few people can taste salt levels as low as 1,000, others not until 3,500 or more.

Salt at Pool Levels Does Not Cause Metal Corrosion

Adding salt to pool water at the levels stated above WILL NOT corrode your pool or damage your pool equipment.

There has been a disturbing trend lately among some pool builders and chemical suppliers to scare people away form saltwater pools by using scare-tactics and fear of pool equipment failure or pool surface degradation. None of these builders or suppliers can back up their claims with actual data and typically use cherry-picked, one-off instances of severe damage which is not necessarily caused by salt.

Salt water in and of itself does not cause metal corrosion. Metal corrosion is entirely dominated by pH and issues with metal corrosion are almost always related to a pool owner not properly keeping their water chemistry balanced.

Over-use of trichlor pucks is one way water can become very acidic and have too low an alkalinity. Salt in water can enhance certain types of corrosion in certain metals (eg, crevice corrosion in aluminum alloys) but the initiation of corrosion is controlled primarily by pH. So don’t be fooled by scare tactics.

Limestone Corrosion

Salt can, in some limited instances, cause accelerated corrosion of certain types of soft limestone, particularly travertine stone and some softer types of flagstone mined in areas of Texas and Oklahoma. These proofs sandstones can allow for the build up of salt inside the microscopic pores of the stones.

If these stones are located in an arid region where precipitation is low and evaporation is high, then the water trapped in these pores will evaporate and the salt that is left behind puts pressure on the pore. Because of the increased pressure from the expanded salt crystal, crack initiation is more likely.

However, this should not deter a pool owner from considering salt water chlorination. Different stone materials can be substituted that are more resistant to salt water OR stone materials can be sealed with a high quality stone sealer.

Stone masons are very familiar with these issues and so, if you are building a pool with natural stone around it, consult with your pool builders stone mason subcontractor to get their opinion on what the best materials are to use in your build.

No Salt for 30 days After New Plaster

One caution with plaster pool surfaces and saltwater pools - when a new plaster surface is applied to a pool, no salt should be added for the first 30 days to allow time for the plaster to cure.

Salt can interfere with the plaster curing process when it is first applied. Salt will often increase the porosity of the plaster surface as well as degrade the calcium carbonate formation process during the curing period.

Most plasterers are aware of this issue and will advise you on the proper start up procedure. If your plaster subcontractor has not reviewed startup procedures with you, you can always look at the National Plaster Council (NPC) Swimming Pool Start-up Procedures for details.

Types of Salt to use in Pools

Salt can be added using solar salt, sold for use in water softeners (sodium chloride). You want the kind that is 99.4% pure or better and which doesn't have any rust inhibitor or other additives. Crystals are fine. Pellets will work but dissolve slightly more slowly.

Pool store salt generally costs more and is more finely ground, but even pellets dissolve quickly enough so that isn't really any advantage. Be aware that salt is a naturally mined or harvested (from slat flats) product.

The type of salt sold for pools is not a highly pure chemical grade of salt and therefore will have some impurities in it form the mining process.

If you are doing an SWG pool startup process, then you could be adding hundreds of pounds of salt to your pool. Even if your salt is 99.5% pure, then every 100 lbs of salt added will add 1/2 pound of “impurities”. This can often lead to cloudy water that will take time for your filter to remove. Most of these impurities are just silica dust or other non-toxic compounds.

Clorox Pool Salt has been reported by multiple members to stain pools.

Testing

Erroneous salt readings is often the first indication of a failing cell. You should always check your salt level with a salt test kit or test strips before adjusting salt levels.

Salt is measured by different methods in various SWGs. It is normal for salt readings to vary by +/-500ppm between a cell reading and the K-1766 salt test. Refer to the Wiki article for your SWG and How Salt Systems Determine Salinity.

Taylor K-1766 Salt Test

The most reliable salt test is the Taylor K-1766 Salt Test.

Testing Errors

If the K-1766 sample is staying milky and not turning maroon when expected check you are using a 10ml sample and not 25ml.

Salt Test Strips

Salt Test Strips can be used though they are not as accurate as the K-1766 Salt Test.