I have this jandy system with a salt cell. I have decided to stop using the salt cell and use chlorine. I took out the old cell and put in a pipe. Now I get this error when I turned on the heater. Seems to be looking for salt %. How do I get the salt cell out of the program?
Jandy error codes 175 182
- Thread starter rubberhead5613
- Start date
- Jul 21, 2013
- 55,447
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Disconnect the 4 wire RS-485 wire from the Aquapure to the Aqualink. THen the Aqualink will not see that you have the control board without the cell.
You should also disconnect the power wiring to the Aquapure.
You should also disconnect the power wiring to the Aquapure.
Thank you for you reply.
I did both things you said to do but the heater is still not coming on.
I'm getting error codes 172 182 185 186.
Not sure what else to do?
I did both things you said to do but the heater is still not coming on.
I'm getting error codes 172 182 185 186.
Not sure what else to do?
- Jul 21, 2013
- 55,447
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Where are you getting those error codes?
I think your heater not coming on is a different problem then your SWG.
Show me pictures of the error codes.
What model heater do you have?
Show us pics of your equipment pad.
@PoolGate can have a look.
I think your heater not coming on is a different problem then your SWG.
Show me pictures of the error codes.
What model heater do you have?
Show us pics of your equipment pad.
@PoolGate can have a look.
- Jul 21, 2013
- 55,447
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
If you disconnected the power to the Aquapure as discussed in Post#2 the Aquapure display would be off.
Show me what you disconnected.
Your heater ignition fault has nothing to do with the Aquapure code.
Check the igniter. They need to be replaced every few years.
www.troublefreepool.com
Show me what you disconnected.
Your heater ignition fault has nothing to do with the Aquapure code.
Check the igniter. They need to be replaced every few years.
Jandy JXI Heaters - Further Reading
www.troublefreepool.com
One pic shows the power cord I disconnected the other shows the salt cell I disconnected. I can manually turn off the heater on the heater itself and then back on and it will run for about 3 minutes before I get the error on the heater
Attachments
- Jul 21, 2013
- 55,447
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
I do appreciate your help.
I disconnected the power, salt cell and the 4 wire you just asked me to unhook.
When I turn everything back on, heater come back on for about 3 minutes then the error shows up.
Not sure what else to do?
I disconnected the power, salt cell and the 4 wire you just asked me to unhook.
When I turn everything back on, heater come back on for about 3 minutes then the error shows up.
Not sure what else to do?
Attachments
- Jul 21, 2013
- 55,447
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Your heater ignition fault has nothing to do with the Aquapure.
Check the igniter. They need to be replaced every few years.