Search results

hello, I have an IC40 w relatively short life. It is Flashing Cell LED. I push the More button to Test. I get a Red LED on the " Low " , Solid Green LED on CELL, and The sanitizer output only have 1 LED. what does that mean? I tried to find a way to search this forum for maybe...

Replaced the pump and took apart some of the components. I see that the Drive Unit Board is burnt at the glued in capacitor. That really sux. Everything is glued in so you cannot repair it. New drive board unit is $800. I got entire new pump for $999.

from all the parts list and video I see. There isnt a capacitor for these pump.

No unions at the inlet outlet. I guess my pool builder skimmed that part. I will get it with the new pump. BTW what is the different between the intelliflo VS against the Superflo VS. Price is big difference. some $1199 vs $699 for superflo VS. I will probably try to order the pump today.

sounds like a plan. just hate to have to cut my intake/ output pipes. Can you recommend said intelliflo without the SVRS? thanks

vs3050 is on the same circuit as the intellichlor. i tried disconnecting the wire for the intellichlor also and it did nothing to help the VS3050 to run. Everything else will work normally with the pump breaker off. It will run the water feature aux pump. once I turn on thevs3050 pump...

Hello pump gods. I have a Pentair intelliflo VS-3050. It is tripping the breaker instantly. I can spin the impeller with my finger. it doesnt seem to be stuck on anything. once I push the pump on, the breaker trips instantly. It was working a few days ago. and we didnt have any rain that...

Southern California. Los Angeles county area. Thanks. - No Autofill - Not much rain in the pass 2 month. - I will add a bag of salt and test again.

I also have a big drop in salt level. using the taylor test kit. It was about 3900ppm about a month ago. It is now at 3200ppm. I didnt really have to fill the pool more than the usual evaporation. Can my filter cause this? I didnt really clean it for the pool open this year yet.

Gotta thank you again. At 3800 seems like I can keep the chlorine level strong at a lower duty cycle. it is now at 60% I think I can go 50%. Also the if I forget to put in acid doesnt seem to foul the SWG cell as easy. So I have been relying on the Pentair cell to tell me proper salt...

I have those kreepy krauly spider disc type suction cleaner. It is a non branded cleaner that cost $70. It cleans really fast but it gets stuck in 3 spot in my pool. So it is pretty much useless. I had a Sandshark before it works ok but really slow never got stuck at those 3 spots. What...

Wow Thank you so much. I added one 40 lb bag of salt and the IC40 is behaving correctly.. Im at good solid green Cell light and water Chlorine level is up . I depended on the IC40 salt level reading at solid green led on salt level. So I wont do that now and test w taylor kit. good...

how high should I take it up to?

on with the saga.. I tested the salt level with the taylor kit. it turn salmon color at 17 drops. so 3400ppm of salt. gave in and changed flow switch and the IC40 still blinking check cell. .. Looked at the fins inside the IC40.. it was Clean!!!! arg. The 2 middle fin have a little bit...

Cell Date 5/26/2016 When i press the More button a quick second time I get a single LED at 80% Still cycling to salt test alternating lights at salt level box once in a while. Im thinking my water chem is all out of wack. We are doing a roof replacement right now and some roof dirt got into...

I will do that this evening. For sure there is enough flow my intelliflo pump is running at good speed for the pool cleaner.

The pool seem to be retaining some Chlorine level but the IC40 just keep cycling to salt testing.

Thanks JoyfulNoise This is what I got from the 3 second More button push diagnostics. Easytouch shows water temp at 85 degrees for reference. Salt level LED in the Solid green at Good Flow LED Green After 3 second More button push LED scroll. the Sanitizer output box I Lit 1 LED 20% then...

Is my IC 40 cell dead? I have no Calcium deposit and the IC40 blink LED indicating Check Cell. The Plates looks ok. one plate have a bit of wear but not a lot It is a 3 year old replacement.

Just did a bunch of wire testing on the Mastertemp. The Heater has it own power wire at 115v. The fireman switch is basically a jumper wire that can be use as a switch. Its an open or close circuit depending if the jumper wire is there or not. Fireman switch operates at 24v. So if you...

hey wow. after year and a half. I finally have to get on the equipments to troubleshoot. Manual start no long worked either. I got a E05 massage and the heater just stops. I did do some research and got all the sensor just in case. I popped the top cover off and looked at the LED's went...

So one of the center plate broke off in my IC40. I assume the chlor Cell is toasted after 5 years of service. Before I get a new Cell at $600 2 Questions 1. Any way to repair it? 2. Anyone tried retrofit to Intex Krystal Clear Saltwater system at way lower price?

Hello, My Mastertemp 400 will no longer auto start with intellitouch spa setting. It use to be automated start when SPA switch is turned on with remote now it wont Now I can only get it to manual start and stop after I use the fireman switch jumper - disconnected the fireman switch with...

Fixed. open the panel tested voltage. apparently the light curcuit power source was connected to the a/c Power outlet on the side of the Easy Touch panel which had a GFCI breaker on it. Reset the power outlet and its fixed. GFCI breaker must have tripped when I used that outlet for some...

I cannot get both my spa nad pool Pentair LED light on. They are controlled by a Pentair EASY Touch 8 panel. I have reset the panel and the light breakers, didnt help. Is there another breaker somewhere for the lights. LED's are about 3 years old they are not turned on often. Hard to...

fast forward, I put together a outdoor fireplace with blocks. For Everyone else, this is more entertaining than the BBQ island since more people enjoy this feature. about 240 block and misc travertine stone.

Thanks. It drain on the floor drain. happen to have one in close proximity. Its about a 12 ft run of copper on each hot and cold. Kitchen is in the other side of that wall. dont plan on insulating it. want to keep it pretty. I even clear coat the copper to keep its color. plus It...

about to have 20-30 pre-teen coming for a pool party. My wife requested I get a outdoor shower going to relieve after pool showering congestion. Ordered a stainless shower panel from ebay and got some copper pipes and sharkbite connection fittings. 1 day of work. Price of the parts shower...