Search results

Folks,, I was just wondering if anybody out there can give me an idea what Im spending per month on the pool pump.. 4 hrs at 300 watts 4 hrs at 740 watts I pay .10KW/Hr

Re: LIQUIDATOR RATE OF FLOW WITH VARIABLE SPEED PUMP QUESTIO What about moving the fitting after the chlorine puck feeder (not in use) to between the filter and heater.

Re: LIQUIDATOR RATE OF FLOW WITH VARIABLE SPEED PUMP QUESTIO I didn't know if I could relocate the inflow fitting closer to pump or something?

FOLKS, NEED SOME OPINIONS HERE... I have a variable speed pump and have tried running at several speeds in the low range but it really affects my rate of feed from the liquidator. In the low speeds my rate of feed is at 0.. Take a look at the pics and see if there would be a better way to...

Re: New Pool - Conroe TX Platinum Pool built our pool. Was happy with the work they did. No problems too date on the pool or equipment. I chose them much for the same reason you did. I recommend the Iaqualink. It has been awesome. Recently added a liquidator and shut off the chlorinator...

Yes sorry. #7. Seven. 70 would be a bit tough and expensive.

In Houston. CYA is 60 so trying to get my FC to 70 by using the liquidator. Pool is crystal clear. Never looked so good.

10-4. I guess I'll give it a dose to bring it to the appropriate level and see what it does.

Also forgot to mention I have a variable speed pump and at low setting the flow meter us at 3 but when the pump sits at my higher RPM setting its above 5. It runs for 4 hrs on low the 3 hrs on high.

Question, Been a week know with the LQ installed and maxed out on the dial. My FC continues to be 4.5 PPM. Will it not increase my ppm over time. I have watched it and it looks like it is working properly. I thought I could raise the FC but maybe I'm wrong. Seems to be maintaining. Also...

Re: Liquidator ! Where to buy? Now installed! whoop Just finished installing the liquidator! Super excited. Install went very easy. I even tapped the fittings into my existing plumbing. All seems good. Current setting is between 4-5 with a startup reading of 4 for FC. What setting do...

Ok folks been doing the bleach thing for about 3 months and I don't believe Ill be using pucks anymore. Where is the best place to purchase a liquidator? I assume you can use bleach or chlorine? Thanks in advance!

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED My problem was one of the volume controls was switched incorrectly at time of install and it finally burned up. I bought a new one and before installing I double checked the switch location. Installed and haven't had any problems either.

My CH is still 425PPM. I have only used bleach since my last episode. Below are my readings from the Taylor K-2006 kit: FC 5.5 PH 7.9 TA 100 CH 425 CYA 73 I have turned off the tri chlor puck feeder to just a 1/4 on and have not used any cal-hypo again. My CYA reading on Monday was 79. I...

So the shock is what raised my CH. I guess I will start using bleach for shock. Anybody want to buy a partial used box of shock? Is it a good idea to shock before a rain storm?

Using the Taylor K-2006 complete FAS-DPD and I used the "please don't shoot me" Leslie's power powder plus.

Folks, My CH was rocking along at 400 then shot up today to 425. We did get alot of rain early this week. Below are my other readings: FC 5.5 PH 7.8 added acid TA 100 CH 425 CYA 49 I am using the dreaded pucks and did shock the pool a bit before the rain. Any comments welcome?

Looks like a platinum builders quote?

I have had the 9400 in service now for a little under a month and I love it. It cleans up the smallest silt and debris to my amazement. I have a little over a 13K gal pool and set it for an hr and 1/2 and it does a great job. It even has a lift mode when done. I do not keep it in the pool...

Call the Jandy Help line. At times they can be helpful.

I am at a lost to figure how long to run my pump on a new pool.. My gals are 13180.. None to little surface debris None to little bottom debris I have almost no vegetation that can get into pool except some flying debris occasional.. I have a Jandy VS 2000 pump.. I am running it at like 1800...

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED I tried something new and it worked better. Still got warm but not hot. I hooked a speaker selector from outdoor speaker depot to the receiver and split the zones with that. I used the r and l channel from the speaker output and left...

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Amp is set at about 60 on the volume control out of 100 and the volume controls tame the patio down so you can hear but still talk and the pool speakers are loud but not obnoxious.

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Thanks, I will try jumping the volume control this weekend and report in

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Switch is in the correct setting

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Receiver is inside in a well ventilated closet. I even put a small fan and that helped a bit but still got hot.

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Is that a question or comment. I'm not sure? Any suggestions?

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Parallel

Re: NEW STEREO RECEIVER GETTING TOO HOT AND SHUT DOWN, NEED Receiver says continues avg output of 80 Watts per channel , min at 8 ohms Volume Controls are 100 watts peak, 8 ohms stereo I have tried using the set up on a zone 2 setting on my home receiver (7.1) and it also got hot but I thought...

Guys,, Please correct my problem.. Equipment- 2 outdoor speakers under porch (8 ohm) 2 rock speakers at pool Outdoor speaker Depot (8 ohm) 2 independent volume controllers from Outdoor Speaker Depot Both have long runs- 100' feet. Used 14 gauge buried in conduit Pioneer VSX-523-K Receiver...