Search results

We moved into a house with a old Coleman/Maxx spa and the heater relay had a short on the board. I ended up replacing the control pack since the cost was just a bit more. I went with a Gecko IN.YE-5 after researching that and the Balboa setups. I called tech support prior for both company's and...

I have an older spa and Im trying to identify this valve. Its from a Coleman/Maxx spa and it goes to the neck jets I believe. I'm not sure if I can just buy the top portion or do I need to replace the entire fitting. I just cant tell if the internal piece is missing or its broken off.

I'm getting anxious to open my pool as well but I live in Michigan the land of eternal coldness. I might still open it in a week I have in years past.

I thought the same thing, but I don't smell gas. I have a gas detection tool. I will verify its not.

No fan, its just the millivolt style

Well I have an old raypak 2100 and I was expecting trouble getting it fired up this year since last year it wouldnt fire. This year lit the pilot light, flipped the switch to on then turned up the thermostat and it fired right up. Now I flipped the switch off and it didnt shutdown. I didnt wait...

Oh wow I was figuring I would be in the range of 5 to 10 degrees

Pool is 512 sqft I have a 12 mil cover Roof has a slight angle east not very windy I would figure maybe a 40 degree increase on a cloudy day.................. :whoot:

What is the weight of a standard 4x20 solar panel filled with water? I live in Michigan and I believe I could fit 4 panels on a section of my roof. What average sort of Temp increase would I see on say a 80 degree day?

Deciding on the liner pattern was difficult :lol: I went back and forth and even called the installer right before he ordered the liner to have him change it. I had rust on portions of my wall and they installer taped the portions of rust then attached foam to them. Seems like common practice...

Yeah just bummed me out I had to wait extra long and paid a bit more for something that wasn't cut to spec and cheaper. :|

I agree when I use the fine mesh bag it will slow down after a few hours but by then it usually has done a pretty decent job, however if you use the standard mesh it doesnt have much of an issue slowing down. I had to adjust the timer and axle pivot degree a few times but compared to vacuuming...

I just had our in-ground liner replaced see post replacing-the-vinyl-liner-inground-t58104.html I went with GLI 28/28 with there gold warranty package cost 1100, only warning he mentioned with the GLI liners and 28 mil is you might feel the seams. I cannot tell you yet if thats true as the pool...

I use the Aquabot T Jet Turbo I like it very simple. For your pool type I mind suggest a scrubber type. The ones I see pop a lot in search results are the Dolphin, Aquabot and Smartpool. I know Aquabot and dolphin have a somewhat large support backing.

Just bought a new clear 12 mil solar cover from in the swim and its a foot too wide and a lot thinner then the last one :hammer:

59 just right :|

Will a 1 hp pump be enough to lift water 9 feet to supply solar panels?

Re: Just got a 2 speed motor would like to wire it to run at Well I think I just purchased the wrong switch. I decided to wire up the high and low, so I went out and bought a DPST switch and Im thinking I should of bought a DPDT? right now it just plugs into a wired outlet 220. :hammer:

Is there one Intermatic timer that can be used to switch pump speeds and run on a schedule?

Well I had to upgrade my pump and now I have a 1hp 2 speed. What would be my turnover rate with my current filter running at low speed?

I have/had a duragals I pump with 3/4hp motor and had the motor replaced with a 2 speed 1 hp cost was 283.00 for the pump and an additional 30.00 to have them install the 2 seals(I did it last time and it was so of a bear to tap the ceramic seal on and seat it correctly. I went through the...

I noticed I have no PSI either is that normal?

So I got my light a bit too late. Im replacing a aqua lumin with a aqua lumin III. I need to attach it with 4 screws and pull the wires through the center 3/4 hub hole. How to I make the hole. Ive read its best to cut an X. Should I drain the water to below the light? Just a little paranoid.

I do have 240 running to the pump

Im in the process of setting up a zwave network and would like to automate my pool pump. I just have a simple pool setup just a 2 speed 1hp pump that runs on low almost always. Any recommendations on a switch. Found this http://www.smarthome-products.com/p-654 ... odule.aspx