Search results

Thank you

Thanks. I'll try that and see.

Yes, I've always held verticle with no pressure and yes, I noticed the TF r0009 bottle gives very small drops so I'm not sure how to record my TA since my Taylor kit is giving 70ppm while my TF IS 110ppm.

Hi, I recently bought the TF test kits refills for my K20006C. When using my Taylor K-2006C to test my TA I get 70ppm, but when using the TF test I kept getting 110ppm. The results are always higher when I use the TF. Now, I'm just confused with the test results. Has anyone have this problem...

Hmm..I didn't manually turn off the bubbler when I switched from Poool Mode to Spa Mode. I will turn the bubbler to off position next time I run Spa mode and see if that works. Thank you.

I had the filter pump set at 2800 and Spa speed at 2900. Thank you for the link. I'll check it out. I don't see any air bubbles coming out of return lines though. However, I do see air bubbles in the spa if I turned on the air bubbles and then turn it off, I see air bubbles after that where...

Hello, I've been getting air bubbles in my filter pump when I turn on Spa Mode and also PSI goes up about 8psi compared to pool mode.. When I run on Pool Mode, there is no air bubbles at all. This started happening right after the TX freeze. The only thing I had to replace after the freeze was...

Updating... we got a new polaris booster pump put in by a pool tech. He used the Polaris tube instead of the big, round 4" pvc pipes (see picture of the new install). Does it matter which is used? Is there one better than the other?

Thank you.

I have the same question also. I hope someone can answer on here.

I usually google everything first.. Did I just skip this one? 😳 thank you :)

Thanks :)

Hi, I left a bottle of Muratic Acid outside in a single digit freezing temperature. Do you think it is still safe to use? Thank you.

Thank you. I'll do all the test soon and adjust what is needed. Our CYA before this storm was 70. It has probably gone down now. Hopefully, won't need too much chlorine now.

Thank you

Hello, My pool is off due to burst pipe and ruined booster pump from the below freezing weather. Now that the weather is warming up to above 60s some days, what should I do to keep my pool from turning green, grow algae, protect my pebbletec plaster, etc while waiting to get pool equipments...

Ahh ok I'm looking up and reading about the mechanical seal. I guess there are more parts that may need to be checked as well and could be replaced instead of buying all new parts...some may be ok. Thank you foe your information.

Thank you so much. I will update once the pupe is repaired and replacing the pump or maybe just the pump house?

I don't see see any damage in the skimmer (where the skimmer basket would normally be). I'm wondering if water that goes into the skimmer, to the underground pipe where I cannot see, would freeze while the skimmer door was blocked? Water is staying in the skimmer basket after I removed the ice...

Hello 👋 The pool has two skimmers. The near skimmer is the one that got blocked, the other was flowing fine. We have a main drain.... That is located at the deepest part of the pool floor right? I just realized I did not drain the Polaris booster pump and found a burst pipe that is...

Oh my ok I guess at 2am Monday at below freezing weather, power was off , while panicking to shut everything off and drained....I didn't drain my Polaris booster pump:( I just saw one pipe that burst. Is my Polaris booster pump ruined now? What about underground pipes?

Hi, I'm trying to to figure out or pictured what is going on inside my skimmer and pipes during the freeze spells. Situation... 2am single digit temperature and high wind Power shut off and then came on right away at 2am (rolling blackouts started) that is how I found out about the skimmer...