Search results

Yep - mentioned that in my post.

I’m seeing another thread talking about a jumper for temp sensor but not sure if that would also affect salinity reading.

Almost 1 year old.

We have recently noticed that our Circulpool RJ 45+ has been acting up. Currently it is showing 133° temperature and no salt when we are measuring 4100 ppm and the temperatures are just normal Florida weather. Last weekend I attempted to clean the salt cell and got very little bubbles and it was...

They did screw down the vent and plugged the jets. Then air escaped somewhere below the cap and in the wall of the raised spa. The question is, is that vent seal so very important all the way up to the vent? Could water be leaking about the venturi chamber?

Hello all - just had a leak detection service out and they found two issues. One is that two of the vents for the raised spa is not holding air pressure. These are simple venturi's, not a blower system. They're thinking that the leaks are happening there because the vents won't hold pressure...

I'm currently fighting with my pool service who keeps shocking my pool cause our leased SWG won't keep up with the rain/drain. Thanks for the comments all!

Living in Florida - we're getting a ton of rain these days. My pool is equipped with a gravity drain (just a hole in the pool to pvc pipe outside the foundation), I think that's what it's called. Depending on how I adjust that pipe this will determine the level the pool will start to drain and...

I really just need the plastics, not the electronics.

I have a Z4 control panel that is just worn out and cracking. I've been keeping it going with clear tape but looking for a better solution. Does anyone have a solution or know where I can just by the case? My board is fine and pristine. Thanks!

Does the Aqualink still run without the interface over the web? Mine looks the same is on its way out.

Also a tip! If you find grit in your jandy valves, loosen them so you can move the handle past the stops and spin them 360° and the grit will be displaced.

Some closure on this. Had Red Rhino out and they found my leak on the main drain line right below the deck surface. I have a pavers on dirt so this explains the small pebbles and the back flowing of water...and the draining down. I'm having the pool remodel company fix the plumbing and the...

It’s pool finish. My valves are below waterline so a lot flows out when I take the valve apart.

I'm going to go clean it out right now and take some pics....I believe it's pool finish (tiny pebble sheen pebbles). It was redone last year.

Hayward Pro Grid DE filter...pic above.

I think I know why I'm getting grit on these valves. When the pump is shut off, water from the straining basket flows backwards through the valves and I'm thinking it's getting caught on the partially opened valves and closed valves...when the valves are reopened, the grit is resting on the...

Are you saying find the RPM that the skimmer pulls and holds dirt down and never go below that RPM? Back to original topic for a sec - how am I getting grit in the skimmer valve? This should be sinking to the bottom. Does this mean I have a leak? I'm getting some bubbles when the pump is...

Funny - I was just in the process of modifying this. I’m now trying 6-8am 3000rpm, 8am-sunset 1500rpm, sunset for 2 hours 2500 with spillover, 10-midnight 1500rpm.

Yes, I have a zodiac Z4. I can run with or without spillover, why do you ask?

Thanks! I'll get some ordered. My other battle is getting a good skim on my new VS pump, finding that right RPM that gets it done.

Hello all - love this forum - you guys are awesome! Just installed Jandy valves on my vacuum side about a month ago. I keep finding that they're getting full of grit when you turn them. I've opened them up once before and cleaned them out and they're starting to show some wear on the seals...

I set AUX3 to cleaner and then it allowed me to setup a speed for that mode. Winning!!